Interface (G-MA)
页面进行中。 |
气体和湿空气网络之间的边界。
类型: EngeeFluids.Interfaces.GasMoistAir
图书馆中的路径:
|
说明
Interface (G-MA) 单元代表气体网络和湿空气网络流之间的连接。边界处的压力、温度和质量流量相等。区块不会在边界上传递每个网络的流体属性。要保持流体属性,请确保*Gas Properties (G)* 区块和*Moist Air Properties (MA)* 区块的设置相同。当潮湿空气离开 MA 端口时,程序块会为其分配 Interface relative humidity 和 Interface trace gas mass fraction 参数值或输入信号值。但是,当潮湿空气进入 MA 端口时,设备会将变量值存储在潮湿空气流中。
您可以选择是保持湿度和边界杂质气体量不变,还是分别使用 W、Tw 和 TG 端口进行设置。
能量守恒
边界能量守恒
其中
-
- 流向端口的能量流量 G;
-
- 流向端口 MA 的能量通量;
-
- 端口的比焓 G;
-
- 端口*MA*的比焓;
-
- 端口 G 的流速;
-
- 端口 MA 的流速。
对于给定的端口横截面积 ,该模块将 和 定义为:
其中
-
- 端口的具体容量 G;
-
- 端口 MA 的具体容量:
边界处混合物的通用气体常数 是两侧液体的函数:
其中
-
- 是干燥空气的气体比常数;
-
- 水蒸气的气体比常数
-
- 杂质气体的比气体常数;
-
- 边界比湿度。当流量从 MA 端口流出时,设备会根据参数设置确定该值:
-
当 Controlled moisture and trace gas 复选框未被选中时,程序块将根据参数 Interface moisture specification 中指定的方法计算 。
-
选中 Controlled moisture and trace gas 时,程序块根据端口 W 或端口 Tw 的输入值计算 。
-
-
- 边界杂质气体的质量分数。当流量从端口 MA 流出时,程序块会根据参数设置确定该值:
-
当 Controlled moisture and trace gas 复选框未选中时,程序块将根据参数值 Interface trace gas mass fraction 或 Interface trace gas mole fraction 计算 。
-
选中 Controlled moisture and trace gas 时,程序块根据 TG 端口的输入值计算 。
-
端口
非定向
#
G
—
气口
气体
Details
与边境天然气有关的非定向口岸。
程序使用名称 |
|
#
马萨诸塞州
—
潮湿气口
潮湿空气
Details
与边界潮湿空气有关的非定向端口。
程序使用名称 |
|
输入
#
TG
—
杂质气体
尺度
Details
决定边界杂质气体分数的端口。
依赖关系
要使用此端口,请选择复选框 Controlled moisture and trace gas 。
数据类型 |
Float64`。 |
复数支持 |
无 |
#
W
—
湿度,无量纲
标量
Details
决定边界湿度的端口。
依赖关系
要使用该端口,请选择 Controlled moisture and trace gas 复选框,并将 Interface moisture specification 设置为 Relative humidity
, Specific humidity
, Mole fraction`或 `Humidity ratio
.
数据类型 |
Float64`。 |
复数支持 |
无 |
#
捻
—
温度,K
标量
Details
根据边界湿温度计确定温度的端口,单位为 K。
依赖关系
要使用该端口,请选择复选框 Controlled moisture and trace gas ,并将参数 Interface moisture specification 设为 Wet-bulb temperature
.
数据类型 |
Float64`。 |
复数支持 |
无 |
参数
参数
# Controlled moisture and trace gas — 在边界控制水分和杂质气体的选项
Details
如果未选中该复选框,设备将在边界保持恒定的湿度和杂质气体。如果选中该复选框,则通过 W 和 TG 端口设置湿度和杂质气体。
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Interface moisture specification —
水分参数
Relative humidity
| Specific humidity
| Mole fraction
| Humidity ratio
| Wet-bulb temperature
Details
选择湿度计算方式:使用相对湿度、比湿度、摩尔分数、湿度系数或湿球温度。
值 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
# Interface relative humidity — 边界相对湿度
Details
边界的相对湿度。区块使用该值计算湿度。
依赖关系
要使用该参数,请取消选中 Controlled moisture and trace gas ,并为参数 Interface moisture specification 在 Relative humidity
.
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Interface trace gas specification —
杂质气体参数化
Mass fraction
| Mole fraction
Details
选择边界杂质气体的参数化方式:使用质量分数或摩尔分数。
值 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
# Interface trace gas mass fraction — 边界杂质气体的质量分数
Details
边界杂质气体的质量分数。
依赖关系
要使用该参数,请清除 Controlled moisture and trace gas 复选框,并将 Interface trace gas specification 设置为 Mass fraction
.
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
# Relative humidity at saturation — 饱和点相对湿度
Details
饱和点的相对湿度。
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Cross-sectional area at ports G and MA —
气体和湿空气开口的横截面积
m^2
| cm^2
| ft^2
| in^2
| km^2
| mi^2
| mm^2
| um^2
| yd^2
Details
气体和湿空气开口的横截面积。
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Inputs outside valid range —
用于监控超出允许范围的输入数据的选项
Limit to valid values
| Error
Details
监控无效输入。如果选择了 `Limit to valid values`则设备在设定范围内饱和输入值。如果选择值为 `Error`则在程序块接收到无效输入值时停止仿真。
值 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
# Interface trace gas mole fraction — 边界杂质气体的摩尔分数
Details
边界杂质气体的摩尔分数。
依赖关系
要使用此参数,请取消选中 Controlled moisture and trace gas ,并将 Interface trace gas specification 设置为 。 Mole fraction
.
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
# Interface specific humidity — 边界比湿
Details
边界的比湿度。区块使用该值计算湿度。
依赖关系
要使用此参数,请取消选中 Controlled moisture and trace gas ,并将 Interface moisture specification 设置为 。 Specific humidity
.
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
# Interface water vapor mole fraction — 边界处水蒸气的摩尔分数
Details
界面处水蒸气的摩尔分数。程序块使用该值计算含水量。
依赖关系
要使用该参数,请取消选中 Controlled moisture and trace gas ,并将 Interface moisture specification 设置为 。 Mole fraction
.
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
# Interface humidity ratio — 边界湿度系数
Details
边界上的湿度系数。区块使用该值计算含水量。
依赖关系
要使用该参数,请取消选中 Controlled moisture and trace gas ,并将 Interface moisture specification 参数设置为 Humidity ratio
.
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Interface wet-bulb temperature —
边界湿球温度
K
| degC
| degF
| degR
| deltaK
| deltadegC
| deltadegF
| deltadegR
Details
界面湿温度计的温度。区块使用该值计算湿度。
依赖关系
要使用该参数,请取消选中 Controlled moisture and trace gas ,并将 Interface moisture specification 设置为 Wet-bulb temperature
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |