Engee 文档

4-Way 3-Position Directional Valve (TL)

导热流体网络中的四线三位置分配器。

类型: EngeeFluids.ThermalLiquid.Valves.DirectionalControl.FourWayThreePosition

图书馆中的路径:

/Physical Modeling/Fluids/Thermal Liquid/Valves & Orifices/Directional Control Valves/4-Way 3-Position Directional Valve (TL)

说明

液压单元 4-Way 3-Position Directional Valve (TL) 是一个带有四个连接管路的换向阀,通常位于热流体网络中的液压缸、泵和油箱之间。分配器的操作由一个单向阀根据 S 端口上的信号控制。分配器有三个位置,以下分别称为中位、正位和负位。可以通过以下参数设置撒布器的基本配置 Neutral spool position open connections 当阀芯向正反方向移动时打开的通道,参数为 Positive spool position open connections и Negative spool position open connections 分别为

可以在参数中设置分配器通道的流量特性。 Orifice parameterization 中设置分配器通道的流量特性,该特性可以是线性关系,也可以是用户提供的表格函数,可应用于一个或所有分配器通道。

分配器配置示例如图所示。

4 way 3 position directional valve il 1 cn

在下图所示的配置中,参数 Neutral spool position open connections 设置为 All closed.当阀芯处于中位时,所有孔口均关闭,无法流动。

4 way 3 position directional valve il 2

在下图所示配置中,参数 Negative spool position open connections 设置为 "P-A 和 B-T"。当端口 S 的信号将阀芯移动到负位置(中性点左侧)时,端口 PA 之间以及端口 BT 之间的通道打开。端口 PB 之间以及端口 AT 之间的通道关闭。

4 way 3 position directional valve il 3

在下面的配置中,参数 Positive spool position open connections 设置为 "P-B 和 A-T"。当端口 S 的信号将阀芯移动到正位置(中性位置的右侧)时,端口 PB 之间以及端口 AT 之间的通道打开,端口 PA 之间以及端口 BT 之间的通道关闭。

4 way 3 position directional valve il 4

这种配置的示意图如下:左侧对应正位置,右侧对应负位置。

4 way 3 position directional valve il 5

阀芯运动和分配器配置

阀芯行程是指通道全开和全关之间的阀芯移动量。可以使用参数 Orifice parameterization и Area characteristics 可用于设置通道特性,如表所示。

Orifice parameterization Identical for all flow paths Different for each flow path

Linear - Area vs. spool travel

阀芯行程等于参数值 Spool travel between closed and open orifice

阀芯行程等于参数值 Spool travel between closed and open orifice 对于每个通道

Tabulated data - Area vs. spool travel

阀芯行程等于参数第一个元素和最后一个元素之间的差值 Spool travel vector

阀芯行程等于参数的第一个元素和最后一个元素之间的差值 Spool travel vector 对于每个通道

Tabulated data - Volumetric flow rate vs. spool travel and pressure drop

阀芯行程等于参数的第一个元素和最后一个元素之差 Spool travel vector, ds

阀芯行程等于参数的第一个元素和最后一个元素之间的差值 Spool travel vector, ds 对于每个通道

下表显示了如何根据位置确定通道阀芯的相对位置。

通道打开时的阀芯位置 阀芯的相对位置

通道始终关闭(通道未选择任何位置)

未使用

通道始终打开(通道选择在正向、中性和负向位置)

未使用

负位置

+ 阀芯行程− S

负位置和中性位置

+ 转轴行程− S

正位置

+ 转轴行程+ S

正位和中位

+ 转轴行程+ S

中立位置

+ 转轴行程− | S|

正负位置

- + 阀芯行程+ | S|

其中 是每个通道规定的最大横截面积时阀芯的位置。当 为负值时,横截面积等于泄漏面积,当通道完全打开时,横截面积等于最大值。通道全开时,相对位置等于阀芯行程,因此如果 值超过阀芯行程,则不会进一步增加通道横截面积。

在参数 Consistency check for neutral spool position open connections 中可以选择是否在违反条件时产生错误:

  • 所有在 Neutral spool position open connections 中指定的所有通道在 S 信号为 0 时都处于打开状态。

  • 所有未在 Neutral spool position open connections 中未指定的所有通道在 S 信号为 0 时关闭。

下表列出了设备的可能配置 4-Way 3-Position Directional Valve (TL) .

配置 参数值

所有四个通道都关闭在中位(默认)。

Static

Positive spool position open connectionsP-A 和 B-T

Neutral spool position open connections : `All closed

Negative spool position open connections P-B和A-T

Spool position at maximum P-A orifice area > P-A 阀芯行程

Spool position at maximum P-B orifice area <−P-B 阀芯行程

Spool position at maximum A-T orifice area <−A-T 阀芯冲程

Spool position at maximum B-T orifice area > B-T 阀芯行程

所有四个通道在中立位置打开。

Static

Positive spool position open connectionsP-A 和 B-T

Neutral spool position open connections : `P-A, P-B, A-T, and B-T

Negative spool position open connections P-B和A-T

Spool position at maximum P-A orifice area < P-A 阀芯行程

Spool position at maximum P-B orifice area >−P-B 阀芯行程

Spool position at maximum A-T orifice area >−A-T 阀芯冲程

Spool position at maximum B-T orifice area < B-T 阀芯行程

通道 A-T 和 B-T 关闭。通道 P-A 和 P-B 正重叠。

Static

Positive spool position open connections 仅 P-A

Neutral spool position open connections : All closed

Negative spool position open connections : 只有P-B

Spool position at maximum P-A orifice area > P-A 阀芯行程

Spool position at maximum P-B orifice area <−P-B 阀芯行程

通道 A-T 和 B-T 打开。通道 P-A 和 P-B 正重叠。

Static

Positive spool position open connectionsP-A 和 B-T

Neutral spool position open connections : `A-T and B-T

Negative spool position open connections P-B和A-T

Spool position at maximum P-A orifice area > P-A 阀芯行程

Spool position at maximum P-B orifice area < -P-B 阀芯行程

Spool position at maximum A-T orifice area >−A-T 阀芯冲程

Spool position at maximum B-T orifice area < B-T 阀芯行程

通道 P-A 和 A-T 在中位时打开。通道 P-B 和 B-T 正重叠。

Static

Positive spool position open connectionsP-B 和 A-T

Neutral spool position open connections : `P-A and A-T

Negative spool position open connections P-A和B-T

Spool position at maximum P-A orifice area < P-A 阀芯行程

Spool position at maximum P-B orifice area > P-B 阀芯行程

Spool position at maximum A-T orifice area > A-T 阀芯行程

Spool position at maximum B-T orifice area <−B-T 阀芯行程

通道 A-T 在中立位置打开。通道 P-B、A-T 和 B-T 有正向重叠。

Static

Positive spool position open connections :`P-A 和 B-T

Neutral spool position open connections :只有`A-T

Negative spool position open connections : `P-B和A-T

Spool position at maximum P-A orifice area > P-A 阀芯行程

Spool position at maximum P-B orifice area <−P-B 阀芯行程

Spool position at maximum A-T orifice area >−A-T 阀芯冲程

Spool position at maximum B-T orifice area > B-T 阀芯行程

通道 B-T 在中立位置打开。通道 P-A、P-B 和 A-T 正重叠。

Static

Positive spool position open connections P-A 和 B-T

Neutral spool position open connections : `仅 B-T

Negative spool position open connections :`P-B 和 A-T

Spool position at maximum P-A orifice area > P-A 阀芯行程

Spool position at maximum P-B orifice area <−P-B 阀芯行程

Spool position at maximum A-T orifice area <−A-T 阀芯冲程

Spool position at maximum B-T orifice area < B-T 阀芯行程

通道 P-A 和 P-B 打开。通道 A-T 和 B-T 正重叠。

Static

Positive spool position open connections :`P-A 和 B-T

Neutral spool position open connections P-A 和 B-T

Negative spool position open connections : `P-B 和 A-T

Spool position at maximum P-A orifice area < P-A 阀芯行程

Spool position at maximum P-B orifice area >−P-B 阀芯行程

Spool position at maximum A-T orifice area <−A-T 阀芯冲程

Spool position at maximum B-T orifice area > B-T 阀芯行程

通道 P-A 在中立位置打开。通道 P-B、A-T 和 B-T 正重叠。

Static

Positive spool position open connections :`P-A 和 B-T

Neutral spool position open connections :只有`P-A

Negative spool position open connections :`P-B 和 A-T

Spool position at maximum P-A orifice area < P-A 阀芯行程

Spool position at maximum P-B orifice area <−P-B 阀芯行程

Spool position at maximum A-T orifice area <−A-T 阀芯冲程

Spool position at maximum B-T orifice area > B-T 阀芯行程

通道 P-B 在中立位置打开。通道 P-A、A-T 和 B-T 正重叠。

Static

Positive spool position open connections :`P-A 和 B-T

Neutral spool position open connections :只有`P-B

Negative spool position open connections :`P-B 和 A-T

Spool position at maximum P-A orifice area > P-A 阀芯行程

Spool position at maximum P-B orifice area >−P-B 阀芯行程

Spool position at maximum A-T orifice area <−A-T 阀芯冲程

Spool position at maximum B-T orifice area > B-T 阀芯行程

通道 P-B 和 B-T 在中位时打开。通道 P-A 和 A-T 正重叠。

Static

Positive spool position open connectionsP-B 和 A-T

Neutral spool position open connections : `P-B and B-T

Negative spool position open connections P-A和B-T

Spool position at maximum P-A orifice area <−P-A 阀芯行程

Spool position at maximum P-B orifice area < P-B 阀芯行程

Spool position at maximum A-T orifice area > A-T 阀芯行程

Spool position at maximum B-T orifice area >−B-T 阀芯行程

通道 P-A、P-B、A-T 和 B-T 在中位时关闭。通道 P-T 在中立位置打开,当阀芯移动时关闭。

Static

Positive spool position open connectionsP-A 和 B-T

Neutral spool position open connections : `P-T only

Negative spool position open connections P-B和A-T

Spool position at maximum P-A orifice area > P-A 阀芯行程

Spool position at maximum P-B orifice area <−P-B 阀芯行程

Spool position at maximum A-T orifice area <−A-T 阀芯冲程

Spool position at maximum B-T orifice area > B-T 阀芯行程

Spool position at maximum P-T orifice area = 任何值

通道 P-A 永久打开。通道 P-B、A-T 和 B-T 在中位时打开。

Static

Positive spool position open connectionsP-A 和 B-T

Neutral spool position open connections : `P-A, P-B, A-T, and B-T

Negative spool position open connections P-A和B-T

Spool position at maximum P-A orifice area < P-A 阀芯行程

Spool position at maximum P-B orifice area < P-B 阀芯行程

Spool position at maximum A-T orifice area = 任何值

Spool position at maximum B-T orifice area >−B-T 阀芯行程

通道 P-B 永久打开。通道 P-A、A-T 和 B-T 在中位时打开。

Static

Positive spool position open connectionsP-B 和 A-T

Neutral spool position open connections : `P-A, P-B, A-T, and B-T

Negative spool position open connections P-A和B-T

Spool position at maximum P-A orifice area >−P-A 阀芯行程

Spool position at maximum A-T orifice area < A-T 阀芯行程

Spool position at maximum B-T orifice area = 任意值

通道 P-A 在中立位置关闭。端口 AT 之间没有通道。

Static

Positive spool position open connections : P-A和B-T

Neutral spool position open connections : `All closed

Negative spool position open connections P-A和B-T

| Spool position at maximum P-A orifice area | > P-A spool stroke

Spool position at maximum P-B orifice area > P-B 阀芯行程

Spool position at maximum B-T orifice area <−B-T 阀芯行程

P-B 通道在中位时关闭。端口 BT 之间没有通道。

Static

Positive spool position open connections : P-B和A-T

Neutral spool position open connections : `All closed

Negative spool position open connections P-A和B-T

Spool position at maximum P-A orifice area <−P-A 阀芯行程

| Spool position at maximum P-B orifice area | > P-B 阀芯行程

Spool position at maximum A-T orifice area > A-T 阀芯行程

通道 P-A 在中位时关闭。通道 A-T 在空档位置打开。

Static

Positive spool position open connectionsP-A 和 B-T

Neutral spool position open connections : `A-T and B-T

Negative spool position open connections P-A和B-T

| Spool position at maximum P-A orifice area | > P-A spool stroke

Spool position at maximum P-B orifice area > P-B 阀芯行程

Spool position at maximum A-T orifice area = 任何值

Spool position at maximum B-T orifice area >−B-T 阀芯行程

通道 P-B 在中位时关闭。B-T 通道在空档位置打开。

Static

Positive spool position open connectionsP-B 和 A-T

Neutral spool position open connections : `A-T and B-T

Negative spool position open connections P-A和B-T

Spool position at maximum P-A orifice area <−P-A 阀芯行程

| Spool position at maximum P-B orifice area | > P-B 阀芯行程

Spool position at maximum A-T orifice area < A-T 阀芯行程

Spool position at maximum B-T orifice area = 任意值

通道 P-B 在中立位置关闭。P-T 通道在空档位置打开。端口 AT 之间没有通道。

Static

Positive spool position open connections : P-A和B-T

Neutral spool position open connections : `P-T only

Negative spool position open connections P-B和A-T

Spool position at maximum P-A orifice area > P-A 阀芯行程

| Spool position at maximum P-B orifice area | > P-B 阀芯行程

Spool position at maximum B-T orifice area <−B-T 阀芯行程

Spool position at maximum P-T orifice area = 任何值

通道 P-A 在中立位置关闭。通道 P-T 在中立位置打开。端口 AT 之间没有通道。

Static

Positive spool position open connections : P-A和B-T

Neutral spool position open connections : `P-T only

Negative spool position open connections P-A和B-T

| Spool position at maximum P-A orifice area | > P-A spool stroke

Spool position at maximum P-B orifice area <−P-B 阀芯行程

Spool position at maximum B-T orifice area > B-T 阀芯行程

Spool position at maximum P-T orifice area = 任何值

分配器通道参数化

参数 Orifice parameterization 中定义了截面面积的计算方法。计算可通过通道参数或表格数据集进行,表格数据集在断面参数中指定 Model Parameterization .如果参数 Area characteristics 设置为 `Identical for all flow paths`或值设置为 `Different for each flow path`如果参数设置为 ,则单元对所有通道使用相同的数据;如果参数设置为 ,则对每个通道设置单独的值。

分配器通道的参数设置 Orifice parameterization 可以是线性或表格形式。

线性参数化

如果参数 Orifice parameterization 如果选择了 "线性 - 面积与阀芯行程",则通道 的流通面积线性取决于阀芯行程和提供给端口 S 的值:

,

其中

  • - 是渠道的最大横截面积(参数值 Maximum orifice area);

  • - 泄漏面积(参数值 Leakage area);

  • - 通道关闭和打开状态之间的阀芯行程(参数值 Spool travel between closed and open orifice);

  • - 阀芯相对位置,从 0 到

的值为负值时,等于 ,当通道全开时,等于 。当通道全开时,相对位置等于阀芯行程,因此超过阀芯行程的值 不会增加横截面积。

注意图中从 的线性增加:

Static

在线性参数化中,当通道接近打开或接近关闭时,可以通过调整平滑系数来保持模拟的数值稳定性。 Smoothing factor .如果参数 Smoothing factor 不等于零,则可确保 之间横截面积的平滑变化。

表格参数化

如果参数 Orifice parameterization 值 "表格数据 - 面积与阀芯行程",则必须定义孔面积与阀芯相对位置之间关系的矢量。 是通道面积矢量的第一个和最后一个元素。 Orifice area vector 分别是

Static

如果选择 "制表数据 - 体积流量与阀芯行程和压降的关系 "进行参数设置 Orifice parameterization 如果选择 "表格数据 - 体积流量与阀芯行程和压降的关系 "进行参数化,则必须设置相对阀芯位置和压降的矢量。根据压降和相对阀芯位置之间的关系计算出容积流量。插值法用于确定给定数据点之间的流速。质量流量是体积流量与密度的乘积。

Static

如果选择 "表列数据 - 质量流量与开度和压降 "进行参数化,则开度和压降的相对位置矢量将被计算出来。 Orifice parameterization 如果选择 "表格数据 - 质量流量与开度和压降 "进行参数化,则必须定义阀芯相对位置和压降的矢量以及相应的质量流量表。插值法用于确定给定数据点之间的流量。

Static

端口

非定向

# P — 导热流体端口
导热流体

Details

工作流体供应。

程序使用名称

port_p

# T — 导热液体端口
导热流体

Details

工作流体的排放。

程序使用名称

port_t

# A — 导热液体端口
导热流体

Details

工作线。

程序使用名称

port_a

# B — 导热流体端口
导热流体

Details

工作线。

程序使用名称

port_b

输入

# S — 分电器阀芯位置
尺度

Details

分配器阀芯的位置(米)。在阀芯的正位置打开的通道在正行程时打开。设定在阀芯负位置的通道在负行程时打开。

数据类型

浮动 64

复数支持

参数

阀门配置

# Positive spool position open connections — 在正位置打开的通道
P-A and B-T | P-A and P-B | P-B and A-T | A-T only | B-T only | P-A only | P-B only | P-A, P-B, and A-B

Details

通道在正位置打开。该参数设置分配器的配置,并根据端口 S 接收到的信号确定阀芯的相对位置。

如果参数 Consistency check for neutral spool position open connections 设置为 Error.

P-A and B-T | P-A and P-B | P-B and A-T | A-T only | B-T only | P-A only | P-B only | P-A, P-B, and A-B

默认值

P-A and B-T

程序使用名称

positive_position_open_orifices

可计算

# Neutral spool position open connections — 在中立位置打开通道
All closed | P-A, P-B, A-T, and B-T | A-T and B-T | P-A and A-T | P-A and B-T | P-A and P-B | P-B and A-T | P-B and B-T | A-T only | B-T only | P-A only | P-B only | P-T only | P-A, A-T, and P-T | P-A, P-B, and A-B | P-B, B-T, and P-T | P-A, P-B, A-T, B-T, P-T

Details

通道在中位打开。该参数定义分配器的配置,并根据端口 S 接收到的信号确定阀芯的相对位置。

如果参数 Consistency check for neutral spool position open connections 设置为 Error.

All closed | P-A, P-B, A-T, and B-T | A-T and B-T | P-A and A-T | P-A and B-T | P-A and P-B | P-B and A-T | P-B and B-T | A-T only | B-T only | P-A only | P-B only | P-T only | P-A, A-T, and P-T | P-A, P-B, and A-B | P-B, B-T, and P-T | P-A, P-B, A-T, B-T, P-T

默认值

All closed

程序使用名称

neutral_position_open_orifices

可计算

# Negative spool position open connections — 在负位置打开的通道
P-A and B-T | P-A and P-B | P-B and A-T | A-T only | B-T only | P-A only | P-B only | P-A, P-B, and A-B

Details

通道在负位置打开。该参数设置分配器的配置,并根据端口 S 接收到的信号确定阀芯的相对位置。

如果参数 Consistency check for neutral spool position open connections 设置为 Error.

P-A and B-T | P-A and P-B | P-B and A-T | A-T only | B-T only | P-A only | P-B only | P-A, P-B, and A-B

默认值

P-B and A-T

程序使用名称

negative_position_open_orifices

可计算

# Consistency check for neutral spool position open connections — 在最大通道横截面积上检查通道配置是否符合设定的线轴位置
None | Error

Details

该参数的值定义了检查在中位打开的通道配置是否与通道最大横截面积时设定的线轴位置一致的必要性。对于每个启用的通道,线轴在中立位置的相对位置必须与设定的配置一致。

None | Error

默认值

None

程序使用名称

neutral_assert_action

可计算

模型参数化

# Area characteristics — 通道特征描述方法
Identical for all flow paths | Different for each flow path

Details

为渠道横截面设置相同或单独的流量特征:

  • Identical for all flow paths- 为分配器的所有通道设置相同的特性。

  • Different for each flow path- 为每个通道设置单独的特性。

在这两种情况下,端口 ABPT 具有相同的横截面积、流量系数和雷诺数,如果参数 Orifice parameterization 设置为 Linear - Area vs. spool travel`或 `Tabulated data - Area vs. spool travel.

Identical for all flow paths | Different for each flow path

默认值

Identical for all flow paths

程序使用名称

area_characteristics

可计算

# Orifice parameterization — 航道面积计算方法
Linear - Area vs. spool travel | Tabulated data - Area vs. spool travel | Tabulated data - Volumetric flow rate vs. spool travel and pressure drop | Tabulated data - Mass flow rate vs. spool travel and pressure drop

Details

一种在建模中计算渠道横截面积的方法。

在表格参数化过程中,可以指定渠道流动特性的非线性轮廓,其形式为流动面积对阀芯位置的依赖性,或容积流量对压力降和阀芯位置的依赖性。

Linear - Area vs. spool travel | Tabulated data - Area vs. spool travel | Tabulated data - Volumetric flow rate vs. spool travel and pressure drop | Tabulated data - Mass flow rate vs. spool travel and pressure drop

默认值

Linear - Area vs. spool travel

程序使用名称

orifice_parameterization

可计算

# Spool travel between closed and open orifice — 最大转轴行程
m | cm | ft | in | km | mi | mm | um | yd

Details

关闭和打开通道状态之间的阀芯冲程。

依赖关系

要使用该参数,请将参数 Area characteristicsIdentical for all flow paths`并为参数 Orifice parameterization 值 `Linear - Area vs. spool travel.

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

0.005 m

程序使用名称

max_spool_travel

可计算

# Maximum orifice area — 航道最大横截面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

航道的最大横截面积。

依赖关系

要使用该参数,请将参数 Area characteristicsIdentical for all flow paths`并为参数 Orifice parameterization 值 `Linear - Area vs. spool travel.

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

1e-4 m^2

程序使用名称

max_area

可计算

# Spool travel vector — 线轴相对位置的矢量值
m | cm | ft | in | km | mi | mm | um | yd

Details

阀芯相对位置的数值矢量。矢量的维数与矢量 Orifice area vector .数值以升序排列,第一个元素必须为 0。表中数据点之间采用线性插值。

依赖关系

要使用该选项,请设置参数 Area characteristicsIdentical for all flow paths`并为参数 Orifice parameterization 值 `Tabulated data - Area vs. spool travel.

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

[0.0, 1.25e-3, 2.5e-3, 3.75e-3, 5e-3] m

程序使用名称

spool_travel_vector

可计算

# Orifice area vector — 航道横截面积的矢量值
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

用于表格参数化的渠道横截面积值矢量。矢量的维数与矢量 Spool travel vector .数值按升序排列。第一个元素是泄漏面积,最后一个元素是最大通道横截面积。数据点之间采用线性插值。

依赖关系

要使用该参数,请将参数 Area characteristicsIdentical for all flow paths`并为参数 Orifice parameterization 值 `Tabulated data - Area vs. spool travel.

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

[1e-10, 1e-5, 4e-5, 6e-5, 1e-4] m^2

程序使用名称

valve_area_vector

可计算

# Spool travel vector, ds — 线轴相对位置的矢量值
m | cm | ft | in | km | mi | mm | um | yd

Details

用于表格式流量参数化的阀芯位置值矢量。阀芯位置矢量的尺寸对应于压差矢量 Pressure drop vector, dp 和体积流量表 Volumetric flow rate table, q(ds,dp) 或质量流量表 Mass flow rate table, mdot(ds,dp) .数值以升序排列,第一个元素必须等于 0。线性插值用于计算中间值。

依赖关系

要使用该选项,请设置参数 Area characteristics 值 `Identical for all flow paths`并为参数 Orifice parameterization 值 `Tabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 "表格数据 - 质量流量与开度和压降的关系"。

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

[0.0, 1.25e-3, 2.5e-3, 3.75e-3, 5e-3] m

程序使用名称

spool_travel_vector_2D

可计算

# Pressure drop vector, dp — 压差矢量
Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

Details

用于表格式流量参数化的压差值矢量。压差矢量的尺寸对应于阀芯位置矢量 Spool travel vector, ds 和体积流量表 Volumetric flow rate table, q(ds,dp) 或质量流量表 Mass flow rate table, mdot(ds,dp) .数值以升序排列。线性插值用于计算中间值。

依赖关系

要使用该参数,请将参数设置为 Area characteristics 值 `Identical for all flow paths`并为参数 Orifice parameterization 值 `Tabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 "表格数据 - 质量流量与开度和压降的关系"。

计量单位

Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

默认值

[-0.1, 0.3, 0.5, 0.7] MPa

程序使用名称

delta_p_vector_2D

可计算

# Volumetric flow rate table, q(ds,dp) — 体积流量表
m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

Details

与压差和阀芯位置值相对应的体积流量矩阵 - 相应矢量的尺寸:

  • - 阀芯位置矢量的元素数 Spool travel vector, ds .

  • - 压降矢量中的元素数 Pressure drop vector, dp .

依赖关系

要使用该参数,请将参数 Area characteristicsIdentical for all flow paths`并为参数 Orifice parameterization 值 `Tabulated data - Volumetric flow rate vs. spool travel and pressure drop.

计量单位

m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

默认值

[-1e-8 2.2e-8 2.8e-8 3.4e-8; -9e-6 1.5e-4 2e-4 2.4e-4; -3.6e-4 6.3e-4 8.1e-4 9.6e-4; -5.4e-4 9.4e-4 1.2e-3 1.4e-3; -9.1e-4 1.6e-3 2.0e-3 2.4e-3] m^3/s

程序使用名称

Vdot_matrix_2D

可计算

# Mass flow rate table, mdot(ds,dp) — 质量流量表
kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

Details

与压差和阀芯位置值相对应的质量流量矩阵 - 相应矢量的尺寸:

  • - 阀芯位置矢量中的元素数 Spool travel vector, ds .

  • - 压降矢量中的元素数 Pressure drop vector, dp .

依赖关系

要使用该参数,请将参数 Area characteristics 值 `Identical for all flow paths`并将参数 Orifice parameterization 为 "表格数据 - 质量流量与开度和压降"。

计量单位

kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

默认值

[-1e-5 1.7e-5 2e-5 2.6e-5; -9.0e-3 3.5e-3 4.5e-3 5.3e-3; -0.36 0.7 0.9 1.06; -0.54 1.96 2.5 3.0; -0.91 6.0 7.7 9.13] kg/s

程序使用名称

mdot_matrix_2D

可计算

# Constant orifice area — 永久开放式渠道的横截面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

在所有位置都打开的通道的横截面积。

依赖关系

要使用该参数,请对参数进行设置:

  • Area characteristicsIdentical for all flow paths.

  • Orifice parameterization 线性 - 面积与线轴行程 "的值或 Tabulated data - Area vs. spool travel.

  • Positive spool position open connections , Neutral spool position open connections , Negative spool position open connections - 至少有一个通道设置在三个位置上。

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

1e-4 m^2

程序使用名称

area_fixed

可计算

# Constant orifice pressure drop vector — 永久开放通道的压差值矢量
Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

Details

在所有位置打开的通道的压差值矢量。压差矢量的尺寸与矢量 Constant orifice volumetric flow rate vectorConstant orifice mass flow rate vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsIdentical for all flow paths.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections , Neutral spool position open connections , Negative spool position open connections - 至少有一个通道设置在三个位置。

计量单位

Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

默认值

[-0.1, 0.3, 0.5, 0.7] MPa

程序使用名称

delta_p_vector_fixed

可计算

# Constant orifice volumetric flow rate vector — 永久开放水道的体积流量矢量
m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

Details

在所有位置打开的通道的体积流量矢量。压差矢量的维数对应于矢量 Constant orifice pressure drop vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsIdentical for all flow paths.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop.

  • Positive spool position open connections , Neutral spool position open connections , Negative spool position open connections - 至少有一个通道设置在三个位置上。

计量单位

m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

默认值

[-9e-4, 1.6e-3, 2.0e-3, 2.4e-3] m^3/s

程序使用名称

Vdot_vector_fixed

可计算

# Constant orifice mass flow rate vector — 永久开放通道的质量流量矢量值
kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

Details

两个位置都打开的通道的质量流量值矢量。压差矢量的维数对应于矢量 Constant orifice pressure drop vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsIdentical for all flow paths.

  • Orifice parameterization表列数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections и Negative spool position open connections - 至少有一个通道同时设置在这两个位置上。

计量单位

kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

默认值

[-0.9, 1.6, 2.0, 2.4] kg/s

程序使用名称

mdot_vector_fixed

可计算

# Reference inflow temperature — 指定质量流量数据的温度
K | degC | degF | degR | deltaK | deltadegC | deltadegF | deltadegR

Details

设置表中质量流量数据的温度。

依赖关系

要使用该参数,请将参数 Orifice parameterizationTabulated data - Mass flow rate vs. spool travel and pressure drop.

计量单位

K | degC | degF | degR | deltaK | deltadegC | deltadegF | deltadegR

默认值

293.15 K

程序使用名称

T_inflow_ref

可计算

# Reference inflow pressure — 表中质量流量数据所对应的压力
Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

Details

指定表格质量流量数据的压力。程序块使用该参数计算第三个参考参数,即参考密度。

依赖关系

要使用该参数,请将参数 Orifice parameterizationTabulated data - Mass flow rate vs. spool travel and pressure drop.

计量单位

Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

默认值

0.101325 MPa

程序使用名称

p_inflow_ref

可计算

# Leakage area — 通道完全关闭时的泄漏面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

通道完全关闭时所有间隙的总和。任何小于此值的面积都等于指定的泄漏面积。该参数通过保持流动的连续性来提高数值解的稳定性。

依赖关系

要使用该参数,请设置参数 Orifice parameterization 值 "线性 - 面积与阀芯行程"。

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

1e-10 m^2

程序使用名称

leakage_area

可计算

# Cross-sectional area at ports P, T, A and B — 分配器入口或出口的面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

端口 ABPT 的横截面积。该面积用于计算通过分配器的质量流量。

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

0.01 m^2

程序使用名称

port_area

可计算

# Discharge coefficient — 流量系数

Details

校正系数是通过分配器的实际质量流量与理论质量流量之比。

依赖关系

要使用该参数,请设置参数 Orifice parameterization 线性 - 面积与阀芯行程比 "或 Tabulated data - Area vs. spool travel.

默认值

0.64

程序使用名称

C_d

可计算

# Critical Reynolds number — 层流雷诺数上限

Details

流经通道时层流的雷诺数上限。

依赖关系

要使用该参数,请设置参数 "线性 - 面积与阀芯行程 "或设置参数 "线性 - 面积与阀芯行程 "或设置参数 "线性 - 面积与阀芯行程"。 Orifice parameterization 线性 - 面积与阀芯行程比 "或 Tabulated data - Area vs. spool travel.

默认值

150.0

程序使用名称

Re_critical

可计算

# Smoothing factor — 数值平滑因子

Details

一个连续的平滑系数,通过修正通道在接近开启和接近关闭位置的特性,确保顺利开启。

依赖关系

要使用该参数,请将参数 "线性 - 面积与阀芯行程 "设为 Orifice parameterization 为 "线性 - 面积与阀芯行程"。

默认值

0.01

程序使用名称

smoothing_factor

可计算

# Pressure recovery — 在扩大面积时是否考虑到压力的增加

Details

当流体从横截面积较小的区域流向横截面积较大的区域时,是否考虑压力的增加。

依赖关系

要使用此参数,请将 "线性 - 面积与阀芯行程 "或 "阀芯行程 "参数设置为 Orifice parameterization 线性 - 面积与阀芯行程比 "或 Tabulated data - Area vs. spool travel.

默认值

false (关掉)

程序使用名称

pressure_recovery

可计算

P-A 孔口

# Spool position at maximum P-A orifice area — 端口 PA 之间最大通道面积上的阀芯位置
m | cm | ft | in | km | mi | mm | um | yd

Details

端口 PA 之间通道完全打开时的阀芯位置。

依赖关系

要使用该参数,请将参数设置为

  • Positive spool position open connections 以下数值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-A and A-T

    • P-A 和 B-T

    • P-A 和 P-B

    • 仅 P-A

    • P-A, A-T, and P-T

    • P-A、P-B 和 A-B

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

只有在参数中未同时设置 P-A 通道时,才会启用该参数: Positive spool position open connections , Neutral spool position open connections и Negative spool position open connections .

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

0.0075 m

程序使用名称

spool_offset_pa

可计算

# P-A spool travel between closed and open orifice — 端口 PA 之间的最大阀芯行程
m | cm | ft | in | km | mi | mm | um | yd

Details

端口 PA 之间的最大阀芯行程。

依赖关系

要使用该参数,请为参数设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationLinear - Area vs. spool travel.

  • Positive spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-A and A-T

    • P-A 和 B-T

    • P-A 和 P-B

    • 仅 P-A

    • P-A, A-T, and P-T

    • P-A、P-B 和 A-B

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

0.005 m

程序使用名称

max_spool_travel_pa

可计算

# P-A maximum orifice area — 端口 PA 之间的最大面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

在全开位置,端口 PA 之间的通道横截面积。

依赖关系

要使用该参数,请为参数进行设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationLinear - Area vs. spool travel.

  • Positive spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-A and A-T

    • P-A 和 B-T

    • P-A 和 P-B

    • 仅 P-A

    • P-A, A-T, and P-T

    • P-A、P-B 和 A-B

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

1e-4 m^2

程序使用名称

max_area_pa

可计算

# P-A orifice spool travel vector — 线轴相对位置矢量
m | cm | ft | in | km | mi | mm | um | yd

Details

线轴位置向量。矢量的维数与矢量 P-A orifice area vector .数值以升序排列,第一个元素必须为 0。表中数据点之间采用线性插值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Area vs. spool travel.

  • Positive spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-A and A-T

    • P-A 和 B-T

    • P-A 和 P-B

    • 仅 P-A

    • P-A, A-T, and P-T

    • P-A、P-B 和 A-B

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

[0.0, 1.25e-3, 2.5e-3, 3.75e-3, 5e-3] m

程序使用名称

spool_travel_vector_pa

可计算

# P-A orifice area vector — 航道横截面积的矢量值
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

用于阀门面积表格参数化的通道横截面积值矢量。矢量的尺寸与矢量 P-A orifice spool travel vector .数值以升序排列,且必须大于 0。

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Area vs. spool travel.

  • Positive spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-A and A-T

    • P-A 和 B-T

    • P-A 和 P-B

    • 仅 P-A

    • P-A, A-T, and P-T

    • P-A、P-B 和 A-B

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

[1e-10, 1e-5, 4e-5, 6e-5, 1e-4] m^2

程序使用名称

valve_area_vector_pa

可计算

# P-A orifice spool travel vector, ds — 线轴相对位置的矢量值
m | cm | ft | in | km | mi | mm | um | yd

Details

用于流量参数表格化的阀芯位置矢量。阀芯位置矢量的尺寸与压差矢量 P-A 孔板压降矢量 dp 和体积流量表 P-A 孔板体积流量表 q(s,dp) 或质量流量表 P-A 孔板质量流量表 mdot(ds,dp) 相对应。数值按升序排列,第一个元素必须为 0。线性插值用于计算中间值。

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 以下数值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-A and A-T

    • P-A 和 B-T

    • P-A 和 P-B

    • 仅 P-A

    • P-A, A-T, and P-T

    • P-A、P-B 和 A-B

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

[0.0, 1.25e-3, 2.5e-3, 3.75e-3, 5e-3] m

程序使用名称

spool_travel_vector_2D_pa

可计算

# P-A orifice pressure drop vector, dp — 压差矢量
Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

Details

用于表格式流量参数化的压差值矢量。压差矢量与阀芯位置矢量相对应 P-A orifice spool travel vector, ds 和体积流量表 P-A孔体积流量表,q(ds,dp) 或质量流量 P-A孔质量流量表,mdot(ds,dp)。数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 以下数值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-A and A-T

    • P-A 和 B-T

    • P-A 和 P-B

    • 仅 P-A

    • P-A, A-T, and P-T

    • P-A、P-B 和 A-B

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

计量单位

Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

默认值

[-0.1, 0.3, 0.5, 0.7] MPa

程序使用名称

delta_p_vector_2D_pa

可计算

# P-A orifice volumetric flow rate table, q(ds,dp) — 体积流量表
m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

Details

与压差和阀芯位置值相对应的体积流量矩阵 - 相应矢量的尺寸:

  • - 阀芯位置矢量的元素数 P-A orifice spool travel vector, ds .

  • - 压降矢量中的元素数 P-A orifice pressure drop vector, dp .

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop.

  • Positive spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-A and A-T

    • P-A 和 B-T

    • P-A 和 P-B

    • 仅 P-A

    • P-A, A-T, and P-T

    • P-A、P-B 和 A-B

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

计量单位

m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

默认值

[-1e-8 2.2e-8 2.8e-8 3.4e-8; -9e-6 1.5e-4 2e-4 2.4e-4; -3.6e-4 6.3e-4 8.1e-4 9.6e-4; -5.4e-4 9.4e-4 1.2e-3 1.4e-3; -9.1e-4 1.6e-3 2.0e-3 2.4e-3] m^3/s

程序使用名称

Vdot_matrix_2D_pa

可计算

# P-A orifice mass flow rate table, mdot(ds,dp) — 质量流量表
kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

Details

与压差和阀芯位置值相对应的质量流量矩阵 - 相应矢量的尺寸:

  • - 阀芯位置矢量中的元素数 P-A orifice spool travel vector, ds .

  • - 压降矢量中的元素数 P-A orifice pressure drop vector, dp .

要使用该参数,请将参数 Area characteristics 值 `Different for each flow path`并将参数 Orifice parameterization 为 "表格数据 - 质量流量与开度和压降"。

计量单位

kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

默认值

[-1e-5 1.7e-5 2e-5 2.6e-5; -9.0e-3 3.5e-3 4.5e-3 5.3e-3; -0.36 0.7 0.9 1.06; -0.54 1.96 2.5 3.0; -0.91 6.0 7.7 9.13] kg/s

程序使用名称

mdot_matrix_2D_pa

可计算

# P-A constant orifice area — 永久开放航道的横截面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

定义为所有位置都开放的渠道的横截面积。

依赖关系

要使用该参数,请为参数设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterization 线性 - 面积与线轴行程 "的值或 Tabulated data - Area vs. spool travel.

  • Positive spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-A and A-T

    • P-A 和 B-T

    • P-A 和 P-B

    • 仅 P-A

    • P-A, A-T, and P-T

    • P-A、P-B 和 A-B

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

只有当 P-A 通道同时设置在三个位置时,才能启用此参数。

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

1e-4 m^2

程序使用名称

area_fixed_pa

可计算

# P-A constant orifice pressure drop vector — 永久开放通道的压差矢量
Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

Details

通道在所有位置打开时的压差值矢量。压差矢量的尺寸与*P-A 恒定孔口体积流量矢量*或 P-A constant mass flow rate vector .数值以升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop.

  • Positive spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-A and A-T

    • P-A 和 B-T

    • P-A 和 P-B

    • 仅 P-A

    • P-A, A-T, and P-T

    • P-A、P-B 和 A-B

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

只有当 P-A 通道同时设置在三个位置时,才能启用此参数。

计量单位

Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

默认值

[-0.1, 0.3, 0.5, 0.7] MPa

程序使用名称

delta_p_vector_fixed_pa

可计算

# P-A constant volumetric flow rate vector — 永久开放航道的体积流量矢量值
m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

Details

在所有位置都打开的通道的体积流量值矢量。压差矢量的维数对应于矢量 P-A constant orifice pressure drop vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop.

  • Positive spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-A and A-T

    • P-A 和 B-T

    • P-A 和 P-B

    • 仅 P-A

    • P-A, A-T, and P-T

    • P-A、P-B 和 A-B

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

只有当 P-A 通道同时设置在三个位置时,才能启用此参数。

计量单位

m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

默认值

[-9e-4, 1.6e-3, 2.0e-3, 2.4e-3] m^3/s

程序使用名称

Vdot_vector_fixed_pa

可计算

# P-A constant mass flow rate vector — 永久开放通道的质量流量矢量值
kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

Details

两个位置都打开的通道的质量流量值矢量。压差矢量的维数对应于矢量 P-A constant orifice pressure drop vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterization表列数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 以下数值之一:

    • P-A 和 B-T"。

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-A and A-T

    • P-A 和 B-T

    • P-A 和 P-B

    • 仅 P-A

    • P-A, A-T, and P-T

    • P-A、P-B 和 A-B

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-A 和 B-T

    • P-A和P-B

    • 仅 P-A

    • P-A、P-B 和 A-B

只有当 P-A 通道同时设置在三个位置时,才能启用此参数。

计量单位

kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

默认值

[-0.9, 1.6, 2.0, 2.4] kg/s

程序使用名称

mdot_vector_fixed_pa

可计算

P-B 孔口

# Spool position at maximum P-B orifice area — 端口 PB 之间最大通道面积上的阀芯位置
m | cm | ft | in | km | mi | mm | um | yd

Details

端口 PB 之间通道完全打开时的阀芯位置。

依赖关系

要使用该参数,请将参数设置为

  • Positive spool position open connections 以下值之一:

    • P-B 和 A-T

    • P-A和P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-B 和 A-T

    • P-B and B-T

    • P-A 和 P-B

    • 只有P-B

    • P-A、P-B 和 A-B

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-B 和 A-T

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

只有在参数中未同时设置 P-B 通道时,才会启用该参数: Positive spool position open connections , Neutral spool position open connections и Negative spool position open connections .

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

-0.0075 m

程序使用名称

spool_offset_pb

可计算

# P-B spool travel between closed and open orifice — 端口 PB 之间的最大阀芯行程
m | cm | ft | in | km | mi | mm | um | yd

Details

端口 PB 之间的最大阀芯行程。

依赖关系

要使用该参数,请为参数设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationLinear - Area vs. spool travel.

  • Positive spool position open connections 以下值之一:

    • P-B 和 A-T`。

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-B 和 A-T

    • P-B and B-T

    • P-A 和 P-B

    • 只有P-B

    • P-A、P-B 和 A-B

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-B 和 A-T

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

0.005 m

程序使用名称

max_spool_travel_pb

可计算

# P-B maximum orifice area — 端口 PB 之间的最大面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

在全开位置,PB 端口之间的横截面积。

依赖关系

要使用该参数,请为参数进行设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationLinear - Area vs. spool travel.

  • Positive spool position open connections 以下值之一:

    • P-B 和 A-T`。

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-B 和 A-T

    • P-B and B-T

    • P-A 和 P-B

    • 只有P-B

    • P-A、P-B 和 A-B

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-B 和 A-T

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

1e-4 m^2

程序使用名称

max_area_pb

可计算

# P-B orifice spool travel vector — 线轴相对位置矢量
m | cm | ft | in | km | mi | mm | um | yd

Details

线轴位置向量。矢量的维数与矢量 P-B orifice area vector .数值以升序排列,第一个元素必须为 0。表中数据点之间采用线性插值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Area vs. spool travel.

  • Positive spool position open connections 以下值之一:

    • P-B 和 A-T`。

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-B 和 A-T

    • P-B and B-T

    • P-A 和 P-B

    • 只有P-B

    • P-A、P-B 和 A-B

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-B 和 A-T

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

[0.0, 1.25e-3, 2.5e-3, 3.75e-3, 5e-3] m

程序使用名称

spool_travel_vector_pb

可计算

# P-B orifice area vector — 航道横截面积的矢量值
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

用于阀门面积表格参数化的通道横截面积值矢量。矢量的尺寸与矢量 P-B orifice spool travel vector .数值以升序排列,且必须大于 0。

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Area vs. spool travel.

  • Positive spool position open connections 以下值之一:

    • P-B 和 A-T`。

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-B 和 A-T

    • P-B and B-T

    • P-A 和 P-B

    • 只有P-B

    • P-A、P-B 和 A-B

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-B 和 A-T

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

[1e-10, 1e-5, 4e-5, 6e-5, 1e-4] m^2

程序使用名称

valve_area_vector_pb

可计算

# P-B orifice spool travel vector, ds — 线轴相对位置的矢量值
m | cm | ft | in | km | mi | mm | um | yd

Details

用于流量参数表格化的阀芯位置矢量。阀芯位置矢量的尺寸与压差矢量 P-B 管口压降矢量 dp 和体积流量表 P-B 管口体积流量表 q(s,dp) 或质量流量表 P-B 管口质量流量表 mdot(ds,dp) 相对应。这些值按升序排列,第一个元素必须等于 0。线性插值用于计算中间值。

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 值之一:

    • P-B 和 A-T`。

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-B 和 A-T

    • P-B and B-T

    • P-A 和 P-B

    • 只有P-B

    • P-A、P-B 和 A-B

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-B 和 A-T

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

[0.0, 1.25e-3, 2.5e-3, 3.75e-3, 5e-3] m

程序使用名称

spool_travel_vector_2D_pb

可计算

# P-B orifice pressure drop vector, dp — 压差矢量
Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

Details

用于表格式流量参数化的压差值矢量。压差矢量与阀芯位置矢量相对应 P-B orifice spool travel vector, ds 和体积流量表 P-B 节流孔体积流量表 q(ds,dp) 或质量流量 P-B 节流孔质量流量表 mdot(ds,dp)。这些数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 值之一:

    • P-B 和 A-T`。

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-B 和 A-T

    • P-B and B-T

    • P-A 和 P-B

    • 只有P-B

    • P-A、P-B 和 A-B

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-B 和 A-T

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

计量单位

Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

默认值

[-0.1, 0.3, 0.5, 0.7] MPa

程序使用名称

delta_p_vector_2D_pb

可计算

# P-B orifice volumetric flow rate table, q(ds,dp) — 体积流量表
m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

Details

与压差和阀芯位置值相对应的体积流量矩阵 - 相应矢量的尺寸:

  • - 阀芯位置矢量的元素数 P-B orifice spool travel vector, ds .

  • - 压降矢量中的元素数 P-B orifice pressure drop vector, dp .

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop.

  • Positive spool position open connections 以下值之一:

    • P-B 和 A-T`。

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-B 和 A-T

    • P-B and B-T

    • P-A 和 P-B

    • 只有P-B

    • P-A、P-B 和 A-B

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-B 和 A-T

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

计量单位

m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

默认值

[-1e-8 2.2e-8 2.8e-8 3.4e-8; -9e-6 1.5e-4 2e-4 2.4e-4; -3.6e-4 6.3e-4 8.1e-4 9.6e-4; -5.4e-4 9.4e-4 1.2e-3 1.4e-3; -9.1e-4 1.6e-3 2.0e-3 2.4e-3] m^3/s

程序使用名称

Vdot_matrix_2D_pb

可计算

# P-B orifice mass flow rate table, mdot(ds,dp) — 质量流量表
kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

Details

与压差和阀芯位置值相对应的质量流量矩阵 - 相应矢量的尺寸:

  • - 阀芯位置矢量中的元素数 P-B orifice spool travel vector, ds .

  • - 压降矢量中的元素数 P-B orifice pressure drop vector, dp .

依赖关系

要使用该参数,请将参数 Area characteristics 值 `Different for each flow path`并将参数 Orifice parameterization 为 "表格数据 - 质量流量与开度和压降"。

计量单位

kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

默认值

[-1e-5 1.7e-5 2e-5 2.6e-5; -9.0e-3 3.5e-3 4.5e-3 5.3e-3; -0.36 0.7 0.9 1.06; -0.54 1.96 2.5 3.0; -0.91 6.0 7.7 9.13] kg/s

程序使用名称

mdot_matrix_2D_pb

可计算

# P-B constant orifice area — 永久开放航道的横截面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

定义为所有位置均开放的航道的横截面积。

依赖关系

要使用该参数,请为参数设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterization 线性 - 面积与线轴行程 "的值或 Tabulated data - Area vs. spool travel.

  • Positive spool position open connections 以下值之一:

    • P-B 和 A-T

    • P-A 和 P-B

    • 仅 P-B

    • P-A、P-B 和 A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-B 和 A-T

    • P-B and B-T

    • P-A 和 P-B

    • 只有P-B

    • P-A, P-B, and A-B

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-B 和 A-T

    • P-A 和 P-B

    • 只有 P-B

    • P-A、P-B 和 A-B` P-A, P-B, and A-B

只有同时将 P-B 通道设置在三个位置时,才能启用此参数。

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

1e-4 m^2

程序使用名称

area_fixed_pb

可计算

# P-B constant orifice pressure drop vector — 永久开放通道的压差矢量
Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

Details

通道在所有位置打开时的压差值矢量。压差矢量的尺寸与*P-B 恒定孔口容积流量矢量*或*P-B 恒定孔口容积流量矢量*相对应。 P-B constant mass flow rate vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 以下数值之一:

    • P-B 和 A-T

    • P-A 和 P-B

    • 只有 P-B

    • P-A、P-B 和 A-B` P-A, P-B, and A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-B 和 A-T

    • P-B and B-T

    • P-A 和 P-B

    • 只有P-B

    • P-A, P-B, and A-B

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-B 和 A-T

    • P-A 和 P-B

    • 只有 P-B

    • P-A、P-B 和 A-B` P-A, P-B, and A-B

只有同时将 P-B 通道设置在三个位置时,才能启用此参数。

计量单位

Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

默认值

[-0.1, 0.3, 0.5, 0.7] MPa

程序使用名称

delta_p_vector_fixed_pb

可计算

# P-B constant volumetric flow rate vector — 开放通道体积常数的矢量
m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

Details

所有位置均为开放通道的容积流量矢量。压差矢量的维度对应于矢量 P-B constant orifice pressure drop vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop.

  • Positive spool position open connections 以下值之一:

    • P-B 和 A-T

    • P-A 和 P-B

    • 只有 P-B

    • P-A、P-B 和 A-B` P-A, P-B, and A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-B 和 A-T

    • P-B and B-T

    • P-A 和 P-B

    • 只有P-B

    • P-A, P-B, and A-B

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-B 和 A-T

    • P-A 和 P-B

    • 只有 P-B

    • P-A、P-B 和 A-B` P-A, P-B, and A-B

只有同时将 P-B 通道设置在三个位置时,才能启用此参数。

计量单位

m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

默认值

[-9e-4, 1.6e-3, 2.0e-3, 2.4e-3] m^3/s

程序使用名称

Vdot_vector_fixed_pb

可计算

# P-B constant mass flow rate vector — 永久开放通道的质量流量矢量值
kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

Details

依赖关系

要使用该参数,请为参数设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterization表列数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 以下数值之一:

    • P-B 和 A-T`。

    • P-A 和 P-B

    • 只有 P-B

    • P-A、P-B 和 A-B` P-A, P-B, and A-B

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • P-B 和 A-T

    • P-B and B-T

    • P-A 和 P-B

    • 只有P-B

    • P-A, P-B, and A-B

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 以下值之一:

    • P-B 和 A-T

    • P-A 和 P-B

    • 只有 P-B

    • P-A、P-B 和 A-B` P-A, P-B, and A-B

只有同时将 P-B 通道设置在三个位置时,才能启用此参数。

计量单位

kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

默认值

[-0.9, 1.6, 2.0, 2.4] kg/s

程序使用名称

mdot_vector_fixed_pb

可计算

A-B 孔口

# Spool position at maximum A-B orifice area — 端口 A 和端口 B 之间最大通道面积上的阀芯位置
m | cm | ft | in | km | mi | mm | um | yd

Details

端口 AB 之间通道完全打开时的阀芯位置。

依赖关系

要使用该参数,请将参数设置为

  • Positive spool position open connections P-A、P-B 和 A-B` 值。

  • Neutral spool position open connections P-A、P-B 和 A-B' 的含义

  • Negative spool position open connections P-A、P-B 和 A-B' 的含义

只有在参数中未同时设置通道 A-B 时,才会启用此参数: Positive spool position open connections , Neutral spool position open connections и Negative spool position open connections .

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

0.0075 m

程序使用名称

spool_offset_ab

可计算

# A-B spool travel between closed and open orifice — 端口 A 和端口 B 之间的最大阀芯行程
m | cm | ft | in | km | mi | mm | um | yd

Details

端口 AB 之间的最大阀芯行程。

依赖关系

要使用该参数,请为参数设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationLinear - Area vs. spool travel.

  • Positive spool position open connections P-A、P-B 和 A-B` 的含义。

  • Neutral spool position open connections P-A、P-B 和 A-B` 的含义

  • Negative spool position open connections P-A、P-B 和 A-B' 的含义

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

0.005 m

程序使用名称

max_spool_travel_ab

可计算

# A-B maximum orifice area — 端口 AB 之间的最大面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

端口 AB 之间的通道在完全打开位置时的横截面积。

依赖关系

要使用该参数,请为参数进行设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationLinear - Area vs. spool travel.

  • Positive spool position open connections P-A、P-B 和 A-B "的值。

  • Neutral spool position open connections P-A、P-B 和 A-B "的含义。

  • Negative spool position open connections P-A、P-B 和 A-B "的含义。

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

1e-4 m^2

程序使用名称

max_area_ab

可计算

# A-B orifice spool travel vector — 线轴相对位置矢量
m | cm | ft | in | km | mi | mm | um | yd

Details

线轴位置向量。矢量的维数与矢量 A-B orifice area vector .数值以升序排列,第一个元素必须为 0。表中数据点之间采用线性插值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Area vs. spool travel.

  • Positive spool position open connections P-A、P-B 和 A-B "的值。

  • Neutral spool position open connections P-A、P-B 和 A-B "的含义。

  • Negative spool position open connections P-A、P-B 和 A-B "的含义。

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

[0.0, 1.25e-3, 2.5e-3, 3.75e-3, 5e-3] m

程序使用名称

spool_travel_vector_ab

可计算

# A-B orifice area vector — 航道横截面积的矢量值
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

用于阀门面积表格参数化的通道横截面积值矢量。矢量的尺寸与矢量 A-B orifice spool travel vector .数值以升序排列,且必须大于 0。

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Area vs. spool travel.

  • Positive spool position open connections P-A、P-B 和 A-B` 的含义。

  • Neutral spool position open connections P-A、P-B 和 A-B` 的含义

  • Negative spool position open connections P-A、P-B 和 A-B' 的含义

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

[1e-10, 1e-5, 4e-5, 6e-5, 1e-4] m^2

程序使用名称

valve_area_vector_ab

可计算

# A-B orifice spool travel vector, ds — 线轴相对位置的矢量值
m | cm | ft | in | km | mi | mm | um | yd

Details

用于表格流量参数化的阀芯位置矢量。阀芯位置矢量的尺寸与压差矢量 A-B 孔口压降矢量 dp 和体积流量表 A-B 孔口体积流量表 q(s,dp) 或质量流量表 A-B 孔口质量流量表 mdot(ds,dp) 相对应。数值按升序排列,第一个元素必须为 0。线性插值用于计算中间值。

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections P-A、P-B 和 A-B 的值。

  • Neutral spool position open connections 指 "P-A、P-B 和 A-B"。

  • Negative spool position open connections P-A、P-B 和 A-B "的含义。

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

[0.0, 1.25e-3, 2.5e-3, 3.75e-3, 5e-3] m

程序使用名称

spool_travel_vector_2D_ab

可计算

# A-B orifice pressure drop vector, dp — 压差矢量
Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

Details

用于表格式流量参数化的压差值矢量。压差矢量与阀芯位置矢量相对应 A-B orifice spool travel vector, ds 和体积流量表 A-B 孔体积流量表 q(ds,dp) 或质量流量 A-B 孔质量流量表 mdot(ds,dp)。这些数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristics 价值 Different for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections P-A、P-B 和 A-B 的值。

  • Neutral spool position open connections 意为 "P-A、P-B 和 A-B"。

  • Negative spool position open connections P-A、P-B 和 A-B "的含义。

计量单位

Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

默认值

[-0.1, 0.3, 0.5, 0.7] MPa

程序使用名称

delta_p_vector_2D_ab

可计算

# A-B orifice volumetric flow rate table, q(ds,dp) — 体积流量表
m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

Details

与压差和阀芯位置值相对应的体积流量矩阵 - 相应矢量的尺寸:

  • - 阀芯位置矢量的元素数 A-B orifice spool travel vector, ds .

  • - 压降矢量中的元素数 A-B orifice pressure drop vector, dp .

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop.

  • Positive spool position open connections P-A、P-B 和 A-B "的值。

  • Neutral spool position open connections P-A、P-B 和 A-B "的含义。

  • Negative spool position open connections P-A、P-B 和 A-B "的含义。

计量单位

m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

默认值

[-1e-8 2.2e-8 2.8e-8 3.4e-8; -9e-6 1.5e-4 2e-4 2.4e-4; -3.6e-4 6.3e-4 8.1e-4 9.6e-4; -5.4e-4 9.4e-4 1.2e-3 1.4e-3; -9.1e-4 1.6e-3 2.0e-3 2.4e-3] m^3/s

程序使用名称

Vdot_matrix_2D_ab

可计算

# A-B orifice mass flow rate table, q(ds,dp) — 质量流量表
kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

Details

与压差和阀芯位置值相对应的质量流量矩阵 - 相应矢量的尺寸:

  • - 阀芯位置矢量中的元素数 A-B orifice spool travel vector, ds .

  • - 压降矢量中的元素数 A-B orifice pressure drop vector, dp .

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterization表列数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 值 `P-A、P-B 和 A-B'。

  • Neutral spool position open connections 值 `P-A、P-B 和 A-B'。

  • Negative spool position open connections P-A、P-B 和 A-B "的含义。

计量单位

kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

默认值

[-1e-5 1.7e-5 2e-5 2.6e-5; -9.0e-3 3.5e-3 4.5e-3 5.3e-3; -0.36 0.7 0.9 1.06; -0.54 1.96 2.5 3.0; -0.91 6.0 7.7 9.13] kg/s

程序使用名称

mdot_matrix_2D_ab

可计算

# A-B constant orifice area — 永久开放航道的横截面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

定义为所有位置均开放的航道的横截面积。

依赖关系

要使用该参数,请为参数设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterization 线性 - 面积与线轴行程 "的值或 Tabulated data - Area vs. spool travel.

  • Positive spool position open connections P-A、P-B 和 A-B "的含义。

  • Neutral spool position open connections P-A、P-B 和 A-B "的含义。

  • Negative spool position open connections P-A、P-B 和 A-B "的含义。

只有当 A-B 通道同时设置在三个位置时,才能启用该参数。

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

1e-4 m^2

程序使用名称

area_fixed_ab

可计算

# A-B constant orifice pressure drop vector — 永久开放通道的压差矢量
Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

Details

通道在所有位置打开时的压差值矢量。压差矢量的尺寸与*A-B 恒定孔口容积流量矢量*或*A-B 恒定孔口容积流量矢量*相对应。 A-B constant mass flow rate vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections P-A、P-B 和 A-B 的值。

  • Neutral spool position open connections P-A、P-B 和 A-B "的含义。

  • Negative spool position open connections P-A、P-B 和 A-B "的含义。

只有当 A-B 通道同时设置在三个位置时,才能启用该参数。

计量单位

Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

默认值

[-0.1, 0.3, 0.5, 0.7] MPa

程序使用名称

delta_p_vector_fixed_ab

可计算

# A-B constant volumetric flow rate vector — 永久开放航道的体积流量矢量值
m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

Details

在所有位置都打开的通道的体积流量值矢量。压差矢量的维数对应于矢量 A-B constant orifice pressure drop vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop.

  • Positive spool position open connections P-A、P-B 和 A-B` 的值。

  • Neutral spool position open connections P-A、P-B 和 A-B' 的含义

  • Negative spool position open connections P-A、P-B 和 A-B' 的含义

只有同时将通道 A-B 设置为三个位置时,才能启用此参数。

计量单位

m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

默认值

[-9e-4, 1.6e-3, 2.0e-3, 2.4e-3] m^3/s

程序使用名称

Vdot_vector_fixed_ab

可计算

# A-B constant mass flow rate vector — 永久开放通道的质量流量矢量值
kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

Details

在所有位置都打开的通道的质量流量值矢量。压差矢量的维数对应于矢量 A-B constant orifice pressure drop vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterization表列数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 值 `P-A、P-B 和 A-B'。

  • Neutral spool position open connections P-A、P-B 和 A-B' 的含义

  • Negative spool position open connections P-A、P-B 和 A-B' 的含义

只有同时将通道 A-B 设置为三个位置时,才能启用此参数。

计量单位

kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

默认值

[-0.9, 1.6, 2.0, 2.4] kg/s

程序使用名称

mdot_vector_fixed_ab

可计算

A-T 孔口

# Spool position at maximum A-T orifice area — 端口 AT 之间最大通道面积上的阀芯位置
m | cm | ft | in | km | mi | mm | um | yd

Details

端口 AT 之间通道完全打开时的阀芯位置。

依赖关系

要使用该参数,请将参数设置为

  • Positive spool position open connections P-B和A-T "或 "仅A-T "值

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A and A-T

    • P-B 和 A-T

    • 仅 A-T

    • P-A, A-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-B 和 A-T "或 "仅 A-T

只有在参数中未同时设置 A-T 通道时,才会启用该参数: Positive spool position open connections , Neutral spool position open connections и Negative spool position open connections .

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

-0.0075 m

程序使用名称

spool_offset_at

可计算

# A-T spool travel between closed and open orifice — 端口 AT 之间的最大阀芯行程
m | cm | ft | in | km | mi | mm | um | yd

Details

端口 AT 之间的最大阀芯行程。

依赖关系

要使用该参数,请为参数设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationLinear - Area vs. spool travel.

  • Positive spool position open connections P-B和A-T "或 "仅A-T "的值

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A and A-T

    • P-B 和 A-T

    • 仅 A-T

    • P-A, A-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-B 和 A-T "或 "仅 A-T

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

0.005 m

程序使用名称

max_spool_travel_at

可计算

# A-T maximum orifice area — 端口 AT 之间的最大面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

在全开位置,端口 AT 之间通道的横截面积。

依赖关系

要使用该参数,请为参数进行设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationLinear - Area vs. spool travel.

  • Positive spool position open connections P-B和A-T "或 "仅A-T "的值

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A and A-T

    • P-B 和 A-T

    • 仅 A-T

    • P-A, A-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-B 和 A-T "或 "仅 A-T

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

1e-4 m^2

程序使用名称

max_area_at

可计算

# A-T orifice spool travel vector — 线轴相对位置矢量
m | cm | ft | in | km | mi | mm | um | yd

Details

线轴位置向量。矢量的维数与矢量 A-T orifice area vector .数值以升序排列,第一个元素必须为 0。表中数据点之间采用线性插值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Area vs. spool travel.

  • Positive spool position open connections P-B和A-T "或 "仅A-T "的值

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A and A-T

    • P-B 和 A-T

    • 仅 A-T

    • P-A, A-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-B 和 A-T "或 "仅 A-T

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

[0.0, 1.25e-3, 2.5e-3, 3.75e-3, 5e-3] m

程序使用名称

spool_travel_vector_at

可计算

# A-T orifice area vector — 航道横截面积的矢量值
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

用于阀门面积表格参数化的通道横截面积值矢量。矢量的尺寸与矢量 A-T orifice spool travel vector .数值以升序排列,且必须大于 0。

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Area vs. spool travel.

  • Positive spool position open connections P-B和A-T "或 "仅A-T "的值

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A and A-T

    • P-B 和 A-T

    • 仅 A-T

    • P-A, A-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-B 和 A-T "或 "仅 A-T

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

[1e-10, 1e-5, 4e-5, 6e-5, 1e-4] m^2

程序使用名称

valve_area_vector_at

可计算

# A-T orifice spool travel vector, ds — 线轴相对位置的矢量值
m | cm | ft | in | km | mi | mm | um | yd

Details

用于流量参数表格化的阀芯位置矢量。阀芯位置矢量的尺寸与压差矢量 A-T 管口压降矢量 dp 和体积流量表 A-T 管口体积流量表 q(s,dp) 或质量流量表 A-T 管口质量流量表 mdot(ds,dp) 相对应。数值按升序排列,第一个元素必须为 0。线性插值用于计算中间值。

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Positive spool position open connectionsP-B 和 A-T仅 A-T

  • Neutral spool position open connections 以下数值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A and A-T

    • P-B 和 A-T

    • 仅 A-T

    • P-A, A-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-B 和 A-T "或 "仅 A-T

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

[0.0, 1.25e-3, 2.5e-3, 3.75e-3, 5e-3] m

程序使用名称

spool_travel_vector_2D_at

可计算

# A-T orifice pressure drop vector, dp — 压差矢量
Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

Details

用于表格式流量参数化的压差值矢量。压差矢量与阀芯位置矢量相对应 A-T orifice spool travel vector, ds 和体积流量表 A-T孔体积流量表,q(ds,dp) 或质量流量 A-T孔质量流量表,mdot(ds,dp)。这些数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Positive spool position open connectionsP-B 和 A-T仅 A-T

  • Neutral spool position open connections 以下数值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A and A-T

    • P-B 和 A-T

    • 仅 A-T

    • P-A, A-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-B 和 A-T "或 "仅 A-T

计量单位

Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

默认值

[-0.1, 0.3, 0.5, 0.7] MPa

程序使用名称

delta_p_vector_2D_at

可计算

# A-T orifice volumetric flow rate table, q(ds,dp) — 体积流量表
m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

Details

与压差和阀芯位置值相对应的体积流量矩阵 - 相应矢量的尺寸:

  • - 阀芯位置矢量的元素数 A-T orifice spool travel vector, ds .

  • - 压降矢量中的元素数 A-T orifice pressure drop vector, dp .

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop.

  • Positive spool position open connections P-B和A-T "或 "仅A-T "的值

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A and A-T

    • P-B 和 A-T

    • 仅 A-T

    • P-A, A-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-B 和 A-T "或 "仅 A-T

计量单位

m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

默认值

[-1e-8 2.2e-8 2.8e-8 3.4e-8; -9e-6 1.5e-4 2e-4 2.4e-4; -3.6e-4 6.3e-4 8.1e-4 9.6e-4; -5.4e-4 9.4e-4 1.2e-3 1.4e-3; -9.1e-4 1.6e-3 2.0e-3 2.4e-3] m^3/s

程序使用名称

Vdot_matrix_2D_at

可计算

# A-T orifice mass flow rate table, mdot(ds,dp) — 体积流量表
kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

Details

与压差和阀芯位置值相对应的质量流量矩阵 - 相应矢量的尺寸:

  • - 阀芯位置矢量中的元素数 A-T orifice spool travel vector, ds .

  • - 压降矢量中的元素数 A-T orifice pressure drop vector, dp .

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterization表列数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 值`P-B 和 A-T`或`仅 A-T`。

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A and A-T

    • P-B 和 A-T

    • 仅 A-T

    • P-A, A-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-B 和 A-T "或 "仅 A-T

计量单位

kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

默认值

[-1e-5 1.7e-5 2e-5 2.6e-5; -9.0e-3 3.5e-3 4.5e-3 5.3e-3; -0.36 0.7 0.9 1.06; -0.54 1.96 2.5 3.0; -0.91 6.0 7.7 9.13] kg/s

程序使用名称

mdot_matrix_2D_at

可计算

# A-T constant orifice area — 永久开放航道的横截面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

定义为所有位置均开放的航道的横截面积。

依赖关系

要使用该参数,请为参数设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterization 线性 - 面积与线轴行程 "的值或 Tabulated data - Area vs. spool travel.

  • Positive spool position open connections P-B和A-T "值或 "仅A-T "值。

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A and A-T

    • P-B 和 A-T

    • 仅 A-T

    • P-A, A-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-B 和 A-T "或 "仅 A-T

只有同时将 A-T 通道设置在三个位置时,才能启用此参数。

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

1e-4 m^2

程序使用名称

area_fixed_at

可计算

# A-T constant orifice pressure drop vector — 永久开放通道的压差矢量
Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

Details

通道在所有位置打开时的压差值矢量。压差矢量的尺寸与*A-T 恒定孔口体积流量矢量*或*A-T 恒定孔口体积流量矢量*相对应。 A-T constant mass flow rate vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 值`P-B 和 A-T`或`仅 A-T`。

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A and A-T

    • P-B 和 A-T

    • 仅 A-T

    • P-A, A-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-B 和 A-T "或 "仅 A-T

只有当 A-T 通道同时设置在三个位置时,才能启用此参数。

计量单位

Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

默认值

[-0.1, 0.3, 0.5, 0.7] MPa

程序使用名称

delta_p_vector_fixed_at

可计算

# A-T constant volumetric flow rate vector — 永久开放航道的体积流量矢量值
m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

Details

在所有位置都打开的通道的体积流量值矢量。压差矢量的维数对应于矢量 A-T constant orifice pressure drop vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop.

  • Positive spool position open connections 值`P-B 和 A-T`或`仅 A-T

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A and A-T

    • P-B 和 A-T

    • 仅 A-T

    • P-A, A-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-B 和 A-T "或 "仅 A-T

只有当 A-T 通道同时设置在三个位置时,才能启用此参数。

计量单位

m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

默认值

[-9e-4, 1.6e-3, 2.0e-3, 2.4e-3] m^3/s

程序使用名称

Vdot_vector_fixed_at

可计算

# A-T constant mass flow rate vector — 永久开放通道的质量流量矢量值
kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

Details

在所有位置都打开的通道的质量流量值矢量。压差矢量的维数对应于矢量 A-T constant orifice pressure drop vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterization表列数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 值`P-B 和 A-T`或`仅 A-T`。

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A and A-T

    • P-B 和 A-T

    • 仅 A-T

    • P-A, A-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-B 和 A-T "或 "仅 A-T

只有当 A-T 通道同时设置在三个位置时,才能启用此参数。

计量单位

kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

默认值

[-0.9, 1.6, 2.0, 2.4] kg/s

程序使用名称

mdot_vector_fixed_at

可计算

B-T 孔口

# Spool position at maximum B-T orifice area — 端口 BT 之间最大通道面积上的阀芯位置
m | cm | ft | in | km | mi | mm | um | yd

Details

端口 BT 之间通道完全打开时的阀芯位置。

依赖关系

要使用该参数,请为参数设置:

  • Positive spool position open connections P-A和B-T "或 "仅B-T "值

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A 和 B-T

    • P-B and B-T

    • 仅 B-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-A 和 B-T "或 "仅 B-T

只有在参数中未同时设置 B-T 通道时,才会启用该参数: Positive spool position open connections , Neutral spool position open connections и Negative spool position open connections .

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

0.0075 m

程序使用名称

spool_offset_bt

可计算

# B-T spool travel between closed and open orifice — 端口 BT 之间的最大阀芯行程
m | cm | ft | in | km | mi | mm | um | yd

Details

端口 BT 之间的最大阀芯行程。

依赖关系

要使用该参数,请为参数设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationLinear - Area vs. spool travel.

  • Positive spool position open connections P-A和B-T "或 "仅B-T "的值

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A 和 B-T

    • P-B and B-T

    • 仅 B-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-A 和 B-T "或 "仅 B-T

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

0.005 m

程序使用名称

max_spool_travel_bt

可计算

# B-T maximum orifice area — 端口 BT 之间的最大面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

在全开位置,端口 BT 之间的横截面积。

依赖关系

要使用该参数,请为参数进行设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationLinear - Area vs. spool travel.

  • Positive spool position open connections P-A和B-T "或 "仅B-T "的值

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A 和 B-T

    • P-B and B-T

    • 仅 B-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-A 和 B-T "或 "仅 B-T

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

1e-4 m^2

程序使用名称

max_area_bt

可计算

# B-T orifice spool travel vector — 线轴相对位置矢量
m | cm | ft | in | km | mi | mm | um | yd

Details

线轴位置向量。矢量的维数与矢量 B-T orifice area vector .数值以升序排列,第一个元素必须为 0。表中数据点之间采用线性插值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Area vs. spool travel.

  • Positive spool position open connections P-A和B-T "或 "仅B-T "的值

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A 和 B-T

    • P-B and B-T

    • 仅 B-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-A 和 B-T "或 "仅 B-T

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

[0.0, 1.25e-3, 2.5e-3, 3.75e-3, 5e-3] m

程序使用名称

spool_travel_vector_bt

可计算

# B-T orifice area vector — 航道横截面积的矢量值
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

用于阀门面积表格参数化的通道横截面积值矢量。矢量的尺寸与矢量 B-T orifice spool travel vector .数值以升序排列,且必须大于 0。

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Area vs. spool travel.

  • Positive spool position open connections P-A和B-T "或 "仅B-T "的值

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A 和 B-T

    • P-B and B-T

    • 仅 B-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-A 和 B-T "或 "仅 B-T

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

[1e-10, 1e-5, 4e-5, 6e-5, 1e-4] m^2

程序使用名称

valve_area_vector_bt

可计算

# B-T orifice spool travel vector, ds — 线轴相对位置的矢量值
m | cm | ft | in | km | mi | mm | um | yd

Details

用于流量参数表格化的阀芯位置矢量。阀芯位置矢量的尺寸与压差矢量 B-T 管口压降矢量 dp 和体积流量表 B-T 管口体积流量表 q(s,dp) 或质量流量表 B-T 管口质量流量表 mdot(ds,dp) 相对应。数值按升序排列,第一个元素必须为 0。线性插值用于计算中间值。

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 值`P-A 和 B-T`或`仅 B-T`。

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A 和 B-T

    • P-B and B-T

    • 仅 B-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-A 和 B-T "或 "仅 B-T

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

[0.0, 1.25e-3, 2.5e-3, 3.75e-3, 5e-3] m

程序使用名称

spool_travel_vector_2D_bt

可计算

# B-T orifice pressure drop vector, dp — 压差矢量
Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

Details

用于表格式流量参数化的压差值矢量。压差矢量与阀芯位置矢量相对应 B-T orifice spool travel vector, ds 和体积流量表 B-T孔体积流量表,q(ds,dp) 或质量流量*B-T孔质量流量表,mdot(ds,dp)*。这些数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 值`P-A 和 B-T`或`仅 B-T`。

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A 和 B-T

    • P-B and B-T

    • 仅 B-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-A 和 B-T "或 "仅 B-T

计量单位

Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

默认值

[-0.1, 0.3, 0.5, 0.7] MPa

程序使用名称

delta_p_vector_2D_bt

可计算

# B-T orifice volumetric flow rate table, q(ds,dp) — 体积流量表
m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

Details

与压差和阀芯位置值相对应的体积流量矩阵 - 相应矢量的尺寸:

  • - 阀芯位置矢量中的元素数 B-T orifice spool travel vector, ds .

  • - 压降矢量中的元素数 B-T orifice pressure drop vector, dp .

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop.

  • Positive spool position open connections P-A和B-T "或 "仅B-T "的值

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A 和 B-T

    • P-B and B-T

    • 仅 B-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections P-A和B-T "或 "仅B-T "的值。

计量单位

m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

默认值

[-1e-8 2.2e-8 2.8e-8 3.4e-8; -9e-6 1.5e-4 2e-4 2.4e-4; -3.6e-4 6.3e-4 8.1e-4 9.6e-4; -5.4e-4 9.4e-4 1.2e-3 1.4e-3; -9.1e-4 1.6e-3 2.0e-3 2.4e-3] m^3/s

程序使用名称

Vdot_matrix_2D_bt

可计算

# B-T orifice mass flow rate table, mdot(ds,dp) — 质量流量表
kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

Details

与压差和阀芯位置值相对应的质量流量矩阵 - 相应矢量的尺寸:

  • - 阀芯位置矢量中的元素数 B-T orifice spool travel vector, ds .

  • - 压降矢量中的元素数 B-T orifice pressure drop vector, dp .

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterization表列数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 值`P-A 和 B-T`或`仅 B-T`。

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A 和 B-T

    • P-B and B-T

    • 仅 B-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections P-A和B-T "或 "仅B-T "的值。

计量单位

kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

默认值

[-1e-5 1.7e-5 2e-5 2.6e-5; -9.0e-3 3.5e-3 4.5e-3 5.3e-3; -0.36 0.7 0.9 1.06; -0.54 1.96 2.5 3.0; -0.91 6.0 7.7 9.13] kg/s

程序使用名称

mdot_matrix_2D_bt

可计算

# B-T constant orifice area — 永久开放航道的横截面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

定义为所有位置均开放的航道的横截面积。

依赖关系

要使用该参数,请为参数设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterization 线性 - 面积与线轴行程 "的值或 Tabulated data - Area vs. spool travel.

  • Positive spool position open connections 值`P-A 和 B-T`或`仅 B-T`。

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A 和 B-T

    • P-B and B-T

    • 仅 B-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-A 和 B-T "或 "仅 B-T

只有当 B-T 通道同时设置在三个位置时,才能启用此参数。

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

1e-4 m^2

程序使用名称

area_fixed_bt

可计算

# B-T constant orifice pressure drop vector — 永久开放通道的压差矢量
Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

Details

通道在所有位置打开时的压差值矢量。压差矢量的尺寸与矢量 B-T 恒定孔口容积流量矢量B-T constant mass flow rate vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterization 值 `Tabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系'。

  • Positive spool position open connections 值`P-A 和 B-T`或`仅 B-T`。

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A 和 B-T

    • P-B and B-T

    • 仅 B-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-A 和 B-T "或 "仅 B-T

只有当 B-T 通道同时设置在三个位置时,才能启用此参数。

计量单位

Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

默认值

[-0.1, 0.3, 0.5, 0.7] MPa

程序使用名称

delta_p_vector_fixed_bt

可计算

# B-T constant volumetric flow rate vector — 永久开放航道的体积流量矢量值
m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

Details

在所有位置都打开的通道的体积流量值矢量。压差矢量的维数对应于矢量 B-T constant orifice pressure drop vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop.

  • Positive spool position open connections 值`P-A 和 B-T`或`仅 B-T

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A 和 B-T

    • P-B and B-T

    • 仅 B-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-A 和 B-T "或 "仅 B-T

只有当 B-T 通道同时设置在三个位置时,才能启用该参数。

计量单位

m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

默认值

[-9e-4, 1.6e-3, 2.0e-3, 2.4e-3] m^3/s

程序使用名称

Vdot_vector_fixed_bt

可计算

# B-T constant mass flow rate vector — 永久开放通道的质量流量矢量值
kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

Details

在所有位置都打开的通道的质量流量值矢量。压差矢量的维数对应于矢量 B-T constant orifice pressure drop vector .数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterization表列数据 - 质量流量与开度和压降的关系

  • Positive spool position open connections 值`P-A 和 B-T`或`仅 B-T`。

  • Neutral spool position open connections 以下值之一:

    • P-A, P-B, A-T, and B-T

    • A-T and B-T

    • P-A 和 B-T

    • P-B and B-T

    • 仅 B-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

  • Negative spool position open connections 值 "P-A 和 B-T "或 "仅 B-T

只有当 B-T 通道同时设置在三个位置时,才能启用该参数。

计量单位

kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

默认值

[-0.9, 1.6, 2.0, 2.4] kg/s

程序使用名称

mdot_vector_fixed_bt

可计算

P-T 孔径

# Spool position at maximum P-T orifice area — 端口 PT 之间最大通道面积上的阀芯位置
m | cm | ft | in | km | mi | mm | um | yd

Details

端口 PT 之间通道完全打开时的阀芯位置。

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Neutral spool position open connections 以下值之一:

    • P-T only

    • P-A, A-T, and P-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

0.0 m

程序使用名称

spool_offset_pt

可计算

# P-T spool travel between closed and open orifice — 端口 PT 之间的最大阀芯行程
m | cm | ft | in | km | mi | mm | um | yd

Details

端口 PT 之间的最大阀芯行程。

依赖关系

要使用该参数,请为参数设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationLinear - Area vs. spool travel.

  • Neutral spool position open connections 以下值之一:

    • P-T only

    • P-A, A-T, and P-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

0.005 m

程序使用名称

max_spool_travel_pt

可计算

# P-T maximum orifice area — 端口 PT 之间的最大面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

在全开位置,端口 PT 之间的通道横截面积。

依赖关系

要使用该参数,请为参数进行设置:

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationLinear - Area vs. spool travel.

  • Neutral spool position open connections 以下值之一:

    • P-T only

    • P-A, A-T, and P-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

1e-4 m^2

程序使用名称

max_area_pt

可计算

# P-T orifice spool travel vector — 线轴相对位置矢量
m | cm | ft | in | km | mi | mm | um | yd

Details

线轴位置向量。矢量的维数与矢量 P-T orifice area vector .数值以升序排列,第一个元素必须为 0。表中数据点之间采用线性插值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Area vs. spool travel.

  • Neutral spool position open connections 以下值之一:

    • P-T only

    • P-A, A-T, and P-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

[0.0, 1.25e-3, 2.5e-3, 3.75e-3, 5e-3] m

程序使用名称

spool_travel_vector_pt

可计算

# P-T orifice area vector — 航道横截面积的矢量值
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

用于阀门面积表格参数化的通道横截面积值矢量。矢量的尺寸与矢量 P-T orifice spool travel vector .数值以升序排列,且必须大于 0。

依赖关系

要使用该参数,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Area vs. spool travel.

  • Neutral spool position open connections 以下值之一:

    • P-T only

    • P-A, A-T, and P-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

[1e-10, 1e-5, 4e-5, 6e-5, 1e-4] m^2

程序使用名称

valve_area_vector_pt

可计算

# P-T orifice spool travel vector, ds — 线轴相对位置的矢量值
m | cm | ft | in | km | mi | mm | um | yd

Details

用于流量参数表格化的阀芯位置矢量。阀芯位置矢量的尺寸与压差矢量 P-T 管口压降矢量 dp 和体积流量表 P-T 管口体积流量表 q(s,dp) 或质量流量表 P-T 管口质量流量表 mdot(ds,dp) 相对应。这些值按升序排列,第一个元素必须等于 0。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Neutral spool position open connections 值之一:

    • P-T only

    • P-A, A-T, and P-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

[0.0, 1.25e-3, 2.5e-3, 3.75e-3, 5e-3] m

程序使用名称

spool_travel_vector_2D_pt

可计算

# P-T orifice pressure drop vector, dp — 压差矢量
Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

Details

用于表格式流量参数化的压差值矢量。压差矢量与阀芯位置矢量相对应 P-T orifice spool travel vector, ds 和体积流量表 P-T孔体积流量表,q(ds,dp) 或质量流量 P-T孔质量流量表,mdot(ds,dp)。这些数值按升序排列。线性插值用于计算中间值。

依赖关系

要使用该选项,请将参数设置为

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop`或 `表格数据 - 质量流量与开度和压降的关系

  • Neutral spool position open connections 值之一:

    • P-T only

    • P-A, A-T, and P-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

计量单位

Pa | GPa | MPa | atm | bar | kPa | ksi | psi | uPa | kbar

默认值

[-0.1, 0.3, 0.5, 0.7] MPa

程序使用名称

delta_p_vector_2D_pt

可计算

# P-T orifice volumetric flow rate table, q(ds,dp) — 体积流量表
m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

Details

与压差和阀芯位置值相对应的体积流量矩阵 - 相应矢量的尺寸:

  • - 阀芯位置矢量的元素数 P-T orifice spool travel vector, ds .

  • - 压降矢量中的元素数 P-T orifice pressure drop vector, dp .

依赖关系

要使用该参数,请将参数设置为 :

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterizationTabulated data - Volumetric flow rate vs. spool travel and pressure drop.

  • Neutral spool position open connections 以下值之一:

    • P-T only

    • P-A, A-T, and P-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

计量单位

m^3/s | m^3/h | cm^3/s | mm^3/s | ft^3/s | lpm | l/s | gpm | gal/s | gal/h

默认值

[-1e-8 2.2e-8 2.8e-8 3.4e-8; -9e-6 1.5e-4 2e-4 2.4e-4; -3.6e-4 6.3e-4 8.1e-4 9.6e-4; -5.4e-4 9.4e-4 1.2e-3 1.4e-3; -9.1e-4 1.6e-3 2.0e-3 2.4e-3] m^3/s

程序使用名称

Vdot_matrix_2D_pt

可计算

# P-T orifice mass flow rate table, mdot(ds,dp) — 质量流量表
kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

Details

与压差和阀芯位置值相对应的质量流量矩阵 - 相应矢量的尺寸:

  • - 阀芯位置矢量中的元素数 P-T orifice spool travel vector, ds .

  • - 压降矢量中的元素数 P-T orifice pressure drop vector, dp .

依赖关系

要使用该参数,请将参数设置为 :

  • Area characteristicsDifferent for each flow path.

  • Orifice parameterization表列数据 - 质量流量与开度和压降的关系

  • Neutral spool position open connections 以下数值之一:

    • P-T only

    • P-A, A-T, and P-T

    • P-B, B-T, and P-T

    • P-A, P-B, A-T, B-T, P-T

计量单位

kg/s | N*s/m | N/(m/s) | lbf/(ft/s) | lbf/(in/s)

默认值

[-1e-5 1.7e-5 2e-5 2.6e-5; -9.0e-3 3.5e-3 4.5e-3 5.3e-3; -0.36 0.7 0.9 1.06; -0.54 1.96 2.5 3.0; -0.91 6.0 7.7 9.13] kg/s

程序使用名称

mdot_matrix_2D_pt

可计算