Engee 文档

Current Transformer

电流互感器 (CT)。

类型: AcausalElectricPowerSystems.Passive.Transformers.Current

图书馆中的路径:

/Physical Modeling/Electrical/Passive/Transformers/Current Transformer

说明

Current Transformer 是一种具有非理想铁芯的电流互感器 (CT)。磁芯可能因其磁性能和尺寸而非理想。

双绕组变压器的等效电路取决于参数 Winding parameterized by 的两种选择:

  • Combined primary and secondary values

nonlinear transformer 1 s

  • Separate primary and secondary values

nonlinear transformer 2 s

其中

  • Req 是绕组的总有源电阻;

  • Leq`为总散射电感;

  • R1 - 第一个绕组的有源电阻;

  • L1` - 第一个绕组的散射电感;

  • R2` - 第二绕组的有源电阻;

  • L2` - 第二绕组的散射电感;

  • Rm - 有源磁化电阻;

  • Lm` - 充磁电感。

下图显示了三绕组变压器的等效电路:

three winding nonlinear transformer 1 s

其中

  • R1 - 第一个绕组的有源电阻;

  • L1`-第一绕组的耗散电感

  • R2` - 第二绕组的有源电阻;

  • L2` - 第二绕组的散射电感

  • R3` - 第三绕组的有源电阻;

  • L3` - 第三绕组的散射电感;

  • Rm - 有源磁化电阻;

  • Lm` - 磁化电感。

该模块为非线性磁化电感的参数化提供了以下选项:

单电感(线性)

电压、电流和磁通量之间的关系由以下公式定义:

,

,

,

其中

  • - 终端电压;

  • - 通过终端的电流

  • - 通过变压器磁化电感的电流;

  • - 寄生并联电导

  • - 第一绕组的匝数;

  • - 磁通量;

  • - 不饱和电感。

一个饱和点

电压、电流和磁通量之间的关系由以下公式定义:

,

,

(直到饱和点)、

(饱和点之后)、

其中

  • - 终端电压;

  • - 通过终端的电流

  • - 通过变压器磁化电感的电流;

  • - 寄生并联电导

  • - 第一绕组的匝数;

  • - 磁通量

  • - 磁通饱和偏置

  • - 不饱和电感

  • - 饱和电感。

磁通量随电流变化的特性

电压、电流和磁通量之间的关系由以下公式定义:

,

,

,

其中

  • - 终端电压;

  • - 通过终端的电流

  • - 通过变压器磁化电感的电流;

  • - 寄生并联电导

  • - 第一绕组的匝数;

  • - 磁通量。

磁通量是通过一个由电流值矢量和相应磁通量值矢量组成的一维表确定的。可以使用负值和正值来指定这些矢量,也可以只使用正值。如果只使用正值数据,矢量必须从 0 开始,而负值数据将通过相对于点(0,0)的对称映射自动计算。

磁感应强度对磁场强度依赖性的表征

电压、电流和磁通量之间的关系由以下公式定义:

,

,

,

,

,

其中

  • - 终端电压;

  • - 通过终端的电流

  • - 通过变压器磁化电感的电流;

  • - 寄生并联电导

  • - 第一绕组的匝数;

  • - 磁通量

  • - 磁感应强度

  • - 磁场强度

  • - 有效磁芯长度

  • - 铁芯的有效横截面积。

磁感应强度是通过一个由磁场强度值矢量和相应磁感应强度值矢量组成的一维表来确定的。可以使用负值和正值来指定这些矢量,也可以只使用正值。如果只使用正值数据,矢量必须从 0 开始,而负值数据将通过相对于点(0,0)的对称映射自动计算。

磁感应强度与磁场强度之间的磁滞关系表征

电压、电流和磁通量之间的关系由以下公式定义:

,

,

,

μ ,

,

其中

  • - 终端电压;

  • - 通过终端的电流

  • - 通过变压器磁化电感的电流;

  • - 寄生并联电导

  • - 第一绕组的匝数;

  • - 磁通量

  • - 磁感应强度

  • μ - 磁常数

  • - 磁场强度;

  • - 铁芯磁化

  • - 有效磁芯长度

  • - 磁芯的有效横截面积。

磁化会导致磁感应强度增加,而磁感应强度的大小取决于磁场强度的当前值 ,以及其先前随时间的变化。吉尔斯-阿瑟顿模型方程用于确定任何时间点的

吉尔斯-阿瑟顿方程的出发点是将磁化效应分为两部分,其中一部分纯粹是有效场强 ( ) 的函数,另一部分是不可逆的,取决于过去的历史:

.

部分称为磁滞磁化,因为它没有磁滞。它由以下关于有效场强当前值的函数来描述:

.

该函数定义了一条饱和曲线,其极限值为 ,饱和点由 (磁滞曲线的形状系数)的值决定。可以大致认为它描述了两条磁滞曲线的平均值。在程序块 Current Transformer 中,我们设置了 和 B-H 磁滞曲线上的点 的值,这些值用于确定 的值。

参数 是可逆磁化系数,决定了哪些行为由 决定,哪些行为由不可逆项 决定。在 Giles-Atherton 模型中,不可逆项由磁场强度的偏导数决定:

δα

δеслиесли .

将该方程与标准一阶微分方程进行比较可以发现,随着场强 H 的增加,不可逆项 与可逆项 相随,但增益可变 δα

跟踪误差的作用是在 δ 符号变化的点上产生滞后。形成不可逆特性的主要参数是 ,称为体耦合系数。参数 α 称为域间耦合系数,也用于确定用于构建磁滞曲线的有效场强:

α .

α 的值会影响磁滞曲线的形状:它越大,曲线与 B 轴的交点就越高。不过,需要注意的是, δα ,在 δ 时必须为正值,在 δ 时必须为负值,这是保持稳定的必要条件。因此,并非所有 α 值都可以接受;典型的最大值为 1e-3

查找 Giles-Atherton 方程系数近似值的步骤

下面的步骤可用于确定方程系数的合适参数:

  1. 指定参数值 Anhysteretic B-H gradient when H is zero ( at ) 加上 B-H 反滞后曲线上的数据点 。根据这些值,可在程序块初始化时确定 α 的值。

  2. 设置 Coefficient for reversible magnetization, c 的值,以便在从 点开始运行模拟时获得正确的初始 B-H 导数。 的值约等于该初始导数与 Anhysteretic B-H gradient when H is zero 的比值。 的值必须大于 "0",小于 "1"。

  3. 位于正滞后曲线上时,设置 Bulk coupling coefficient, K 的值,使其近似等于 的值。

  4. α 的极小值开始,逐渐增大 的值,当 穿过 时,调整 的值。典型值范围为 1e-41e-3。过大的值会导致 B-H 曲线的导数趋于无穷大,这是不符合实际情况的,会导致运行时断言错误。

可能需要多次执行这些步骤才能与预定义的 B-H 曲线很好地匹配。

伏安特性 (VAC)

根据给定的 VAC,计算磁感应矢量 和电流矢量 ,以使用磁通-电流特性:

,

,

其中

  • - 分别是定义变压器 VAC 的矢量、参数值 Voltage vector for V-I option, (secondary side - RMS)Current vector for V-I option, (secondary side - RMS)

  • - 第一个绕组的匝数,参数值 First winding number of turns

  • - 网络频率,参数值 System frequency

端口

非定向

# + — 初级绕组正极
电力

Details

电气端口,代表具有正极性的初级绕组端子。

程序使用名称

p1

# - — 初级绕组的负极
电力

Details

电气端口,代表具有负极性的初级绕组端子。

程序使用名称

n1

# 1+ — 第一次级绕组的正极
电力

Details

电气端口,代表具有正极性的第一次级绕组的端子。

依赖关系

要使用该端口,请将参数 Include burdenModel the burden externally.

程序使用名称

p2

# 1- — 第一次级绕组的负极
电力

Details

电口,代表负极性的第一次级绕组的端子。

依赖关系

要使用该端口,请将参数 Include burdenModel the burden externally.

程序使用名称

n2

# 2+ — 第二次级绕组的正极
电力

Details

电气端口,代表具有正极性的第二次级绕组的端子。

依赖关系

要使用该端口,请将参数 Include burdenModel the burden externally,并设置参数 Number of windings 参数值 Three, Four, Five`或 `Six.

程序使用名称

p3

# 2- — 第二次级绕组的负极
电力

Details

电口,代表极性为负的第二次级绕组的端子。

依赖关系

要使用该端口,请将参数 Include burdenModel the burden externally,并设置参数 Number of windings 参数值 Three, Four, Five`或 `Six.

程序使用名称

n3

# 3+ — 第三个二次绕组的正极
电力

Details

电口,代表第三个二次绕组的端子,具有正极性。

依赖关系

要使用该端口,请将参数 Include burdenModel the burden externally,并设置参数 Number of windings 参数值 Four, Five`或 `Six.

程序使用名称

p4

# 3- — 第三个二次绕组的负极
电力

Details

电口,代表第三个二次绕组的端子,极性为负。

依赖关系

要使用该端口,请将参数 Include burdenModel the burden externally,并设置参数 Number of windings 参数值 Four, Five`或 `Six.

程序使用名称

n4

# 4+ — 第四个次级绕组的正极
电力

Details

电口,代表第四个二次绕组的端子,具有正极性。

依赖关系

要使用该端口,请将参数 Include burdenModel the burden externally,并设置参数 Number of windingsFive`或 `Six.

程序使用名称

p5

# 4- — 第四个二次绕组的负极
电力

Details

电口,代表第四个二次绕组的端子,极性为负。

依赖关系

要使用该端口,请将参数 Include burdenModel the burden externally,并设置参数 Number of windingsFive`或 `Six.

程序使用名称

n5

# 5+ — 第五个二次绕组的正极
电力

Details

电气端口,代表第五个二次绕组的端子,具有正极性。

依赖关系

要使用该端口,请将参数 Include burdenModel the burden externally,并设置参数 Number of windingsSix.

程序使用名称

p6

# 5- — 第五个二次绕组的负极
电力

Details

电气端口,代表负极性第五个次级绕组的端子。

依赖关系

要使用该端口,请将参数 Include burdenModel the burden externally,并设置参数 Number of windingsSix.

程序使用名称

n6

输出

# i1 — 第一次级绕组的电流
尺度

Details

第一个二次绕组的电流。

依赖关系

要使用该端口,请将参数 Include burdenModel the burden internally.

数据类型

Float64.

复数支持

# i2 — 第二个次级绕组的电流。
尺度

Details

第二个二次绕组的电流。

依赖关系

要使用该端口,请将参数 Include burdenModel the burden internally,并设置参数 Number of windings 参数值 Three, Four, Five`或 `Six.

数据类型

Float64`。

复数支持

# i3 — 第三个二次绕组的电流
尺度

Details

第三个二次绕组的电流。

依赖关系

要使用该端口,请将参数 Include burdenModel the burden internally,并设置参数 Number of windings 参数值 Four, Five`或 `Six.

数据类型

Float64`。

复数支持

# i4 — 第四个二次绕组的电流
尺度

Details

第四个次级绕组的电流。

依赖关系

要使用该端口,请将参数 Include burdenModel the burden internally,并设置参数 Number of windingsFive`或 `Six.

数据类型

Float64`。

复数支持

# i5 — 第五次二次绕组电流
尺度

Details

第五个次级绕组的电流。

依赖关系

要使用该端口,请将参数 Include burdenModel the burden internally,并设置参数 Number of windingsSix.

数据类型

Float64.

复数支持

参数

主机

# Number of windings — 在两绕组、三绕组、四绕组、五绕组和六绕组变压器之间切换
Two | Three | Four | Five | Six

Details

双绕组、三绕组、四绕组、五绕组和六绕组变压器之间的切换。

  • Two- 该装置模拟双绕组变压器。

  • Three- 该模块模拟三绕组变压器。

  • Four- 该模块模拟四绕组变压器。

  • Five- 该模块模拟五绕组变压器。

  • Six- 该模块模拟六绕组变压器。

Two | Three | Four | Five | Six

默认值

Two

程序使用名称

N_windings

可计算

# Turns ratio parameterization by — 用于设置 CT 变压器变比的选项
Number of turns | Current ratio

Details

选择下列方法之一设置 CT 变压器变比:

  • Number of turns- 通过匝数。

  • Current ratio- 通过额定电流。

Number of turns | Current ratio

默认值

Number of turns

程序使用名称

turns_ratio_parameterization

可计算

# First winding number of turns — 第一绕组的匝数

Details

变压器第一绕组导线的匝数。

依赖关系

要使用该参数,请将 Turns ratio parameterization by 设置为以下值 Number of turns.

默认值

1

程序使用名称

N_1

可计算

# Second winding number of turns — 第二绕组的匝数

Details

变压器第二绕组导线的匝数。

依赖关系

要使用该参数,请将 Turns ratio parameterization by 设置为 Number of turns.

默认值

2000

程序使用名称

N_2

可计算

# Third winding number of turns — 第三绕组匝数

Details

变压器第三绕组导线的匝数。

依赖关系

要使用该参数,请将 Turns ratio parameterization by 设置为 Number of turns`并将 Number of windings 设置为 `Three, Four, Five`或 `Six.

默认值

2000

程序使用名称

N_3

可计算

# Fourth winding number of turns — 第四绕组匝数

Details

变压器第四绕组导线的匝数。

依赖关系

要使用该参数,请将 Turns ratio parameterization by 设置为 Number of turns, 并将 Number of windings 设置为 Four, Five`或 `Six.

默认值

2000

程序使用名称

N_4

可计算

# Fifth winding number of turns — 第五绕组匝数

Details

变压器第五绕组导线的匝数。

依赖关系

要使用该参数,请将 Turns ratio parameterization by 设置为 Number of turns`并将 Number of windings 设置为 `Five`或 `Six.

默认值

2000

程序使用名称

N_5

可计算

# Sixth winding number of turns — 第六绕组匝数

Details

变压器第六绕组导线的匝数。

依赖关系

要使用该参数,请将 Turns ratio parameterization by 设置为 Number of turns`并将 Number of windings 设置为 `Six.

默认值

2000

程序使用名称

N_6

可计算

# First winding nominal current — 第一绕组的额定电流
A | MA | kA | mA | nA | pA | uA

Details

第一个绕组的额定电流。

依赖关系

要使用该参数,请将 Turns ratio parameterization by 设置为 。 Current ratio.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

2000.0 A

程序使用名称

I1_rated

可计算

# Secondary winding nominal current — 每个次级绕组的额定电流
A | MA | kA | mA | nA | pA | uA

Details

每个二次绕组的额定电流。

依赖关系

要使用此参数,请将 Turns ratio parameterization by 设置为 。 Current ratio.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

1.0 A

程序使用名称

I2_rated

可计算

# Winding parameterized by — 绕组分布表示类型
Combined primary and secondary values | Separate primary and secondary values

Details

绕组的耗散方式。定义为

  • Combined primary and secondary values- 使用集中的电阻值和电感值,代表初级和次级绕组中的综合泄漏。

  • Separate primary and secondary values- 使用单独的电阻和电感值代表初级和次级绕组中的泄漏。

依赖关系

要使用该参数,请将 Number of windings 设置为 Two.

Combined primary and secondary values | Separate primary and secondary values

默认值

Combined primary and secondary values

程序使用名称

winding_parameterization

可计算

# Combined winding resistance — 绕组总有效电阻
Ohm | GOhm | MOhm | kOhm | mOhm

Details

集中等效有功电阻 Req,表示第一绕组和第二绕组的功率损耗总和。

依赖关系

要使用该参数,请将 Winding parameterized by 设置为 Combined primary and secondary values.

计量单位

Ohm | GOhm | MOhm | kOhm | mOhm

默认值

0.01 Ohm

程序使用名称

R_eq

可计算

# Combined leakage inductance — 总散射电感
H | mH | nH | uH

Details

累积等效电感 Leq,即初级和次级绕组的磁通损耗总和。

依赖关系

要使用该参数,请将 Winding parameterized by 设置为 Combined primary and secondary values.

计量单位

H | mH | nH | uH

默认值

0.0001 H

程序使用名称

L_eq

可计算

# First winding resistance — 第一绕组的有源电阻
Ohm | GOhm | MOhm | kOhm | mOhm

Details

有功电阻 R1,表示第一绕组的功率损耗。

依赖关系

要使用该参数,请将 Winding parameterized by 设置为 Separate primary and secondary values`或将 Number of windings 设置为 `Three, Four, Five`或 `Six.

计量单位

Ohm | GOhm | MOhm | kOhm | mOhm

默认值

0.01 Ohm

程序使用名称

R_1

可计算

# First leakage inductance — 第一绕组的耗散电感
H | mH | nH | uH

Details

电感 L1,表示第一个绕组的磁通损耗。

依赖关系

要使用该参数,请将 Winding parameterized by 设置为 Separate primary and secondary values`或将 Number of windings 设置为 `Three, Four, Five`或 `Six.

计量单位

H | mH | nH | uH

默认值

0.0001 H

程序使用名称

L_1

可计算

# Second winding resistance — 第二绕组的有源电阻
Ohm | GOhm | MOhm | kOhm | mOhm

Details

有功电阻 R2,表示第二个绕组的功率损耗。

依赖关系

要使用该参数,请将 Winding parameterized by 设置为 Separate primary and secondary values`或将 Number of windings 设置为 `Three, Four, Five`或 `Six.

计量单位

Ohm | GOhm | MOhm | kOhm | mOhm

默认值

0.01 Ohm

程序使用名称

R_2

可计算

# Second leakage inductance — 第二绕组的耗散电感
H | mH | nH | uH

Details

电感 L2,表示第二个绕组的磁通损耗。

依赖关系

要使用该参数,请将 Winding parameterized by 设置为 Separate primary and secondary values`或将 Number of windings 设置为 `Three, Four, Five`或 `Six.

计量单位

H | mH | nH | uH

默认值

0.0001 H

程序使用名称

L_2

可计算

# Third winding resistance — 第三绕组的有源电阻
Ohm | GOhm | MOhm | kOhm | mOhm

Details

有功电阻 R3,表示第三个绕组的功率损耗。

依赖关系

要使用该参数,请将 Number of windings 设置为 Three, Four, Five`或 `Six.

计量单位

Ohm | GOhm | MOhm | kOhm | mOhm

默认值

0.01 Ohm

程序使用名称

R_3

可计算

# Third leakage inductance — 第三绕组的耗散电感
H | mH | nH | uH

Details

表示第三个绕组磁通损耗的 L3 电感值。

依赖关系

要使用该参数,请将 Number of windings 设置为 Three, Four, Five`或 `Six.

计量单位

H | mH | nH | uH

默认值

0.0001 H

程序使用名称

L_3

可计算

# Fourth winding resistance — 第四绕组的有源电阻
Ohm | GOhm | MOhm | kOhm | mOhm

Details

有功电阻 R4,表示第四绕组的功率损耗。

依赖关系

要使用该参数,请将 Number of windings 设置为 Four, Five`或 `Six.

计量单位

Ohm | GOhm | MOhm | kOhm | mOhm

默认值

0.01 Ohm

程序使用名称

R_4

可计算

# Fourth leakage inductance — 第四绕组的耗散电感
H | mH | nH | uH

Details

表示第四绕组磁通损耗的 L4 电感值。

依赖关系

要使用该参数,请将 Number of windings 设置为 Four, Five`或 `Six.

计量单位

H | mH | nH | uH

默认值

0.0001 H

程序使用名称

L_4

可计算

# Fifth winding resistance — 第五绕组的有源电阻
Ohm | GOhm | MOhm | kOhm | mOhm

Details

有功电阻 R5,表示第五绕组的功率损耗。

依赖关系

要使用该参数,请将 Number of windings 设置为 Five`或 `Six.

计量单位

Ohm | GOhm | MOhm | kOhm | mOhm

默认值

0.01 Ohm

程序使用名称

R_5

可计算

# Fifth leakage inductance — 第五绕组的耗散电感
H | mH | nH | uH

Details

表示第五绕组磁通损耗的 L5 电感值。

依赖关系

要使用该参数,请将参数 Number of windings 设置为 Five`或 `Six.

计量单位

H | mH | nH | uH

默认值

0.0001 H

程序使用名称

L_5

可计算

# Sixth winding resistance — 第六绕组的有源电阻
Ohm | GOhm | MOhm | kOhm | mOhm

Details

有功电阻 R6,表示第六绕组的功率损耗。

依赖关系

要使用该参数,请将 Number of windings 设置为 Six.

计量单位

Ohm | GOhm | MOhm | kOhm | mOhm

默认值

0.01 Ohm

程序使用名称

R_6

可计算

# Sixth leakage inductance — 第六绕组的耗散电感
H | mH | nH | uH

Details

表示第六绕组磁通损耗的 L6 电感值。

依赖关系

要使用该参数,请将参数 Number of windings 设置为 Six.

计量单位

H | mH | nH | uH

默认值

0.0001 H

程序使用名称

L_6

可计算

磁化率

# Magnetization resistance — 有源磁化电阻
Ohm | GOhm | MOhm | kOhm | mOhm

Details

有源电阻 Rm 代表变压器铁芯中的磁损耗。

计量单位

Ohm | GOhm | MOhm | kOhm | mOhm

默认值

100.0 Ohm

程序使用名称

R_m

可计算

# Magnetization inductance parameterized by — 块参数化
Single inductance (linear) | Single saturation point | Magnetic flux versus current characteristic | Magnetic flux density versus magnetic field strength characteristic | Magnetic flux density versus magnetic field strength characteristic with hysteresis | Voltage versus current characteristic

Details

区块参数化的一种方法。定义为

  • Single inductance (linear)- 指定匝数、非饱和和饱和电感值、饱和磁通量和寄生并联电导率。该选项默认使用。

  • Single saturation point- 指定匝数、非饱和电感和寄生并联电导的值。

  • Magnetic flux versus current characteristic- 除了匝数和寄生并联电导值外,还给出了电流矢量和磁通量矢量,以完成磁通-电流表。

  • Magnetic flux density versus magnetic field strength characteristic- 除了匝数和寄生并联电导值外,还要给出磁芯的有效长度和横截面积,以及磁场强度矢量和磁感应强度矢量,以完成磁感应强度与磁场强度表。

  • Magnetic flux density versus magnetic field strength characteristic with hysteresis- 除磁芯匝数、有效长度和横截面积外,还给出了磁滞 B-H 曲线的初始导数值、B-H 曲线某点的磁感应强度和磁场强度,以及可逆磁化系数、体积耦合系数和域间耦合系数,以确定磁感应强度与电流值和磁场强度历史的函数关系。

  • Voltage versus current characteristic- 通过伏安特性(VAC)设置饱和度。

Single inductance (linear) | Single saturation point | Magnetic flux versus current characteristic | Magnetic flux density versus magnetic field strength characteristic | Magnetic flux density versus magnetic field strength characteristic with hysteresis | Voltage versus current characteristic

默认值

Voltage versus current characteristic

程序使用名称

saturation_parameterization

可计算

# Magnetic field strength vector, H — 磁场强度值矢量
A/m

Details

用于填写磁感应强度与磁场强度关系表的磁场强度值。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设为 。 Magnetic flux versus current characteristic.

计量单位

A/m

默认值

[0.0, 200.0, 400.0, 600.0, 800.0, 1000.0] A/m

程序使用名称

H_vector

可计算

# Magnetic flux density vector, B — 磁感应强度矢量
G | T

Details

用于填写磁感应强度与磁场强度关系表的磁感应强度值。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设置为 Magnetic flux versus current characteristic.

计量单位

G | T

默认值

[0.0, 0.81, 1.25, 1.42, 1.48, 1.49] T

程序使用名称

B_vector

可计算

# Effective length — 有效芯长
m | cm | ft | in | km | mi | mm | um | yd

Details

有效磁芯长度,即磁通路径的平均长度。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设置为 Magnetic flux density versus magnetic field strength characteristic`或 `Magnetic flux density versus magnetic field strength characteristic with hysteresis.

计量单位

m | cm | ft | in | km | mi | mm | um | yd

默认值

0.2 m

程序使用名称

effective_length

可计算

# Effective cross-sectional area — 有效截面积
m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

Details

磁芯的有效截面积,即磁通路径的平均面积。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设置为 Magnetic flux density versus magnetic field strength characteristic`或 `Magnetic flux density versus magnetic field strength characteristic with hysteresis.

计量单位

m^2 | cm^2 | ft^2 | in^2 | km^2 | mi^2 | mm^2 | um^2 | yd^2

默认值

2e-4 m^2

程序使用名称

A_effective

可计算

# Unsaturated inductance — 不饱和电感
H | mH | nH | uH

Details

变压器在线性区工作时使用的电感值。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设置为 Single inductance (linear)`或 `Single saturation point.

计量单位

H | mH | nH | uH

默认值

4e-2 H

程序使用名称

L_m

可计算

# Saturated inductance — 可饱和电感
H | mH | nH | uH

Details

变压器在饱和区工作时使用的电感值。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设置为 Single saturation point.

计量单位

H | mH | nH | uH

默认值

1e-2 H

程序使用名称

L_m_sat

可计算

# Current vector, i — 电流向量
A | MA | kA | mA | nA | pA | uA

Details

用于填充磁通量-电流表的电流值。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设置为 Magnetic flux versus current characteristic.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

[0.0, 0.4, 0.8, 1.2, 1.6, 2.0] A

程序使用名称

i_vector

可计算

# Magnetic flux vector, Φ — 磁通量矢量
Wb | N*m/A | mN*m/A

Details

用于填充磁通量-电流表的磁通量值。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设置为 Magnetic flux versus current characteristic.

计量单位

Wb | N*m/A | mN*m/A

默认值

[0.0, 0.161, 0.25, 0.284, 0.295, 0.299] * 1e-3 Wb

程序使用名称

Phi_vector

可计算

# Current vector for V-I option, (secondary side - RMS) — 电流有效值向量 VAC
A | MA | kA | mA | nA | pA | uA

Details

SAC 电流有效值向量。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设为 Voltage versus current characteristic.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

[0.0, 0.1414, 0.2828, 0.4243, 0.5657, 0.7071] A

程序使用名称

I_RMS_vector

可计算

# Voltage vector for V-I option, (secondary side - RMS) — 电压有效值向量 VAC
V | MV | kV | mV

Details

VAC 电压有效值矢量。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设置为 Voltage versus current characteristic.

计量单位

V | MV | kV | mV

默认值

[0.0, 7.1530, 11.1072, 12.6178, 13.1065, 13.2842] V

程序使用名称

V_RMS_vector

可计算

# System frequency — 网络频率
Hz | GHz | MHz | kHz

Details

网络频率。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 参数设置为 Voltage versus current characteristic.

计量单位

Hz | GHz | MHz | kHz

默认值

50.0 Hz

程序使用名称

f

可计算

# Saturation magnetic flux — 饱和磁通量
Wb | N*m/A | mN*m/A

Details

变压器达到饱和时的磁通值。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设置为 Single saturation point.

计量单位

Wb | N*m/A | mN*m/A

默认值

0.00016 Wb

程序使用名称

Phi_sat

可计算

# Anhysteretic B-H gradient when H is zero — 零场强附近 B-H 磁滞曲线的导数
H/m | mH/m | nH/m | uH/m | H/km | mH/km | T*m/A

Details

零场强附近无磁滞(无滞后)B-H 曲线的导数。设置为正磁滞和负磁滞曲线导数的平均值。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设置为 Magnetic flux density versus magnetic field strength characteristic with hysteresis.

计量单位

H/m | mH/m | nH/m | uH/m | H/km | mH/km | T*m/A

默认值

0.005 T*m/A

程序使用名称

dB_dH_0

可计算

# Flux density point on anhysteretic B-H curve — 磁滞曲线 B-H 上一点的磁感应强度值
G | T

Details

指定磁滞曲线上某一点的磁感应强度值。最精确的选项是选择正磁滞曲线和负磁滞曲线重合时的高磁场强度点。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设置为 Magnetic flux density versus magnetic field strength characteristic with hysteresis.

计量单位

G | T

默认值

1.49 T

程序使用名称

B_anhysteretic

可计算

# Corresponding field strength — 相应场强
A/m

Details

参数 Flux density point on anhysteretic B-H curve 给出的点的相应场强。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设置为 Magnetic flux density versus magnetic field strength characteristic with hysteresis.

计量单位

A/m

默认值

1000.0 A/m

程序使用名称

H_anhysteretic

可计算

# Coefficient for reversible magnetization, c — 可逆磁化系数

Details

可逆磁化率。该值必须大于零,小于一。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设置为 Magnetic flux density versus magnetic field strength characteristic with hysteresis.

默认值

0.1

程序使用名称

c

可计算

# Bulk coupling coefficient, K — 体积耦合系数
A/m

Details

吉尔斯-阿瑟顿模型的一个参数,主要决定 B-H 曲线与零磁感应强度线交叉时的磁场强度大小。

依赖关系

要使用该参数,请将 Magnetization inductance parameterized by 设置为 Magnetic flux density versus magnetic field strength characteristic with hysteresis.

计量单位

A/m

默认值

200.0 A/m

程序使用名称

K

可计算

# Inter-domain coupling factor, α — 域间系数

Details

吉尔斯-阿瑟顿参数,主要影响 B-H 曲线与零场强线的交点。典型值范围为 "1e-4 "到 "1e-3"。

依赖关系

要使用该参数,请将参数 Magnetization inductance parameterized by 设置为 Magnetic flux density versus magnetic field strength characteristic with hysteresis.

默认值

1e-4

程序使用名称

alpha

可计算

# Interpolation option — 插值选项
Linear | Smooth

Details

查找表的插值选项。定义为

  • Linear- 选择该选项可获得最佳性能。

  • Smooth- 选择该选项可获得具有连续一阶导数的连续曲线。

Linear | Smooth

默认值

Linear

程序使用名称

interpolation_option

可计算

负担

# Include burden — 接通/断开 CT 次级绕组的负载

Details

如果该参数设置为 `Model the burden internally`如果该参数设置为该值,则内部负载连接至二次绕组,输出端口将从电气端口变为方向端口(标量端口)。

默认值

false (关掉)

程序使用名称

include_burden

可计算

# Burden type — 载荷类型
R | L | Series RL

Details

负载类型:

  • R- 主动式。

  • L- 电感式。

  • Series RL- 串联有源电感

依赖关系

要使用该参数,请将参数 Include burden 设置为 Model the burden internally.

R | L | Series RL

默认值

R

程序使用名称

burden_type

可计算

# Second winding burden resistance — 第一负载的有源阻抗
Ohm | GOhm | MOhm | kOhm | mOhm

Details

第一个负载的有功电阻。

依赖关系

要使用该参数,请将参数设置为

  • Include burdenModel the burden internally;

  • Burden typeR`或 `Series RL;

计量单位

Ohm | GOhm | MOhm | kOhm | mOhm

默认值

5.0 Ohm

程序使用名称

R_burden2

可计算

# Second winding burden inductance — 第一负载的电感
H | mH | nH | uH

Details

第一个负载的电感。

依赖关系

要使用该参数,请将参数设置为

  • Include burdenModel the burden internally;

  • Burden typeL`或 `Series RL;

计量单位

H | mH | nH | uH

默认值

0.001 H

程序使用名称

L_burden2

可计算

# Third winding burden resistance — 第二个负载的有源电阻
Ohm | GOhm | MOhm | kOhm | mOhm

Details

第二个负载的有功电阻。

依赖关系

要使用该参数,请将参数设置为

  • Include burdenModel the burden internally;

  • Burden typeR`或 `Series RL;

  • Number of windingsThree, Four, Five`或 `Six.

计量单位

Ohm | GOhm | MOhm | kOhm | mOhm

默认值

5.0 Ohm

程序使用名称

R_burden3

可计算

# Third winding burden inductance — 第二个负载的电感
H | mH | nH | uH

Details

第二个负载的电感。

依赖关系

要使用该参数,请将参数设置为

  • Include burdenModel the burden internally;

  • Burden typeL`或 `Series RL;

  • Number of windingsThree, Four, Five`或 `Six.

计量单位

H | mH | nH | uH

默认值

0.001 H

程序使用名称

L_burden3

可计算

# Fourth winding burden resistance — 第三个负载的有源电阻
Ohm | GOhm | MOhm | kOhm | mOhm

Details

第三个负载的有功电阻。

依赖关系

要使用该参数,请将参数设置为

  • Include burdenModel the burden internally;

  • Burden typeR`或 `Series RL;

  • Number of windingsFour, Five`或 `Six.

计量单位

Ohm | GOhm | MOhm | kOhm | mOhm

默认值

5.0 Ohm

程序使用名称

R_burden4

可计算

# Fourth winding burden inductance — 第三负载的电感
H | mH | nH | uH

Details

第三负载电感。

依赖关系

要使用该参数,请将参数设置为

  • Include burdenModel the burden internally;

  • Burden typeL`或 `Series RL;

  • Number of windingsFour, Five`或 `Six.

计量单位

H | mH | nH | uH

默认值

0.001 H

程序使用名称

L_burden4

可计算

# Fifth winding burden resistance — 第四负载的有源电阻
Ohm | GOhm | MOhm | kOhm | mOhm

Details

第四个负载的有功电阻。

依赖关系

要使用该参数,请为参数设置:

  • Include burdenModel the burden internally;

  • Burden typeR`或 `Series RL;

  • Number of windingsFive`或 `Six.

计量单位

Ohm | GOhm | MOhm | kOhm | mOhm

默认值

5.0 Ohm

程序使用名称

R_burden5

可计算

# Fifth winding burden inductance — 第四负载的电感
H | mH | nH | uH

Details

第四负载电感。

依赖关系

要使用该参数,请为参数设置:

  • Include burdenModel the burden internally;

  • Burden typeL`或 `Series RL;

  • Number of windingsFive`或 `Six.

计量单位

H | mH | nH | uH

默认值

0.001 H

程序使用名称

L_burden5

可计算

# Sixth winding burden resistance — 第五负载的有源阻力
Ohm | GOhm | MOhm | kOhm | mOhm

Details

第五个负载的有功电阻。

依赖关系

要使用该参数,请将参数设置为

  • Include burdenModel the burden internally;

  • Burden typeR`或 `Series RL;

  • Number of windingsSix.

计量单位

Ohm | GOhm | MOhm | kOhm | mOhm

默认值

5.0 Ohm

程序使用名称

R_burden6

可计算

# Sixth winding burden inductance — 第五负载电感
H | mH | nH | uH

Details

第五负载电感。

依赖关系

要使用该参数,请为参数设置:

  • Include burdenModel the burden internally;

  • Burden typeL`或 `Series RL;

  • Number of windingsSix.

计量单位

H | mH | nH | uH

默认值

0.001 H

程序使用名称

L_burden6

可计算

初始条件

# Combined leakage current — 总耗散电感的初始电流
A | MA | kA | mA | nA | pA | uA

Details

总耗散电感电流的初始值。

依赖关系

要使用该参数,请将 Winding parameterized by 设为 Combined primary and secondary values.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

0.0 A

程序使用名称

i_Leq_start

可计算

# First leakage inductance current — 第一绕组的初始电流 耗散电感
A | MA | kA | mA | nA | pA | uA

Details

变压器第一绕组损耗电感电流的初始值。

依赖关系

要使用该参数,请将 Winding parameterized by 设置为 Separate primary and secondary values`或将 Number of windings 设置为 `Three, Four, Five`或 `Six.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

0.0 A

程序使用名称

i_L1_start

可计算

# Second leakage inductance current — 第二绕组的初始电流 耗散电感
A | MA | kA | mA | nA | pA | uA

Details

变压器第二绕组损耗电感电流的初始值。

依赖关系

要使用该参数,请将 Winding parameterized by 设置为 Separate primary and secondary values`或将 Number of windings 设置为 `Three, Four, Five`或 `Six.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

0.0 A

程序使用名称

i_L2_start

可计算

# Third leakage inductance current — 第三绕组的初始电流 耗散电感
A | MA | kA | mA | nA | pA | uA

Details

变压器第三绕组损耗电感电流的初始值。

依赖关系

要使用该参数,请将参数 Number of windings 设置为以下值 Three, Four, Five`或 `Six.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

0.0 A

程序使用名称

i_L3_start

可计算

# Fourth leakage inductance current — 第四绕组的初始电流 耗散电感
A | MA | kA | mA | nA | pA | uA

Details

变压器第四绕组损耗电感电流的初始值。

依赖关系

要使用该参数,请将参数 Number of windings 设置为以下值 Four, Five`或 `Six.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

0.0 A

程序使用名称

i_L4_start

可计算

# Fifth leakage inductance current — 第五绕组的初始电流 耗散电感
A | MA | kA | mA | nA | pA | uA

Details

变压器第五绕组损耗电感电流的初始值。

依赖关系

要使用该参数,请将 Number of windings 设置为 Five`或 `Six.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

0.0 A

程序使用名称

i_L5_start

可计算

# Sixth leakage inductance current — 第六绕组的初始电流 耗散电感
A | MA | kA | mA | nA | pA | uA

Details

变压器第六绕组损耗电感电流的初始值。

依赖关系

要使用该参数,请将参数 Number of windings 设置为 Six.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

0.0 A

程序使用名称

i_L6_start

可计算

# Specify magnetization inductance state by — 选项,用于设置初始状态
Current | Magnetic flux

Details

设置初始状态的选项。设置为

  • Current- 根据通过互感器的初始电流设置互感器的初始状态。该选项默认使用。

  • Magnetic flux- 通过磁通量设置互感器的初始状态。

依赖关系

要使用该参数,请将参数 Magnetization inductance parameterized by 设置为 。 Magnetic flux density versus magnetic field strength characteristic with hysteresis.

Current | Magnetic flux

默认值

Current

程序使用名称

saturation_start_option

可计算

# Magnetization inductance current — 初始充磁电感电流
A | MA | kA | mA | nA | pA | uA

Details

用于计算零时磁通量值的初始电流值。这是流经变压器磁化电感的电流。总磁化电流包括通过有源磁化电阻的电流和通过磁化电感的电流。

依赖关系

该参数仅在以下情况下使用 `Current`参数 Specify magnetization inductance state by 时才使用该参数。

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

0.0 A

程序使用名称

i_Lm_start

可计算

# Magnetization inductance magnetic flux — 充磁电感的初始磁通量
Wb | N*m/A | mN*m/A

Details

零时的磁通量值。

依赖关系

该参数仅在 Magnetic flux Specify magnetization inductance state by 时使用。

计量单位

Wb | N*m/A | mN*m/A

默认值

0.0 Wb

程序使用名称

Phi_start

可计算

# Magnetization inductance magnetic flux density — 充磁电感的初始磁感应强度
G | T

Details

零时的磁感应强度。

依赖关系

该参数在 Magnetization inductance parameterized by 设置为 时使用。 Magnetic flux density versus magnetic field strength characteristic with hysteresis.

计量单位

G | T

默认值

0.0 T

程序使用名称

B_start

可计算

# Magnetization inductance field strength — 初始磁感应强度
A/m

Details

零时的磁场强度值。

依赖关系

该参数用于 Magnetization inductance parameterized by 设置为 时。 Magnetic flux density versus magnetic field strength characteristic with hysteresis.

计量单位

A/m

默认值

0.0 A/m

程序使用名称

H_start

可计算

# Second winding burden inductance initial current — 第一负载的初始感应电流
A | MA | kA | mA | nA | pA | uA

Details

第一个负载的初始电感电流。

依赖关系

要使用该参数,请将参数设置为

  • Include burdenModel the burden internally;

  • Burden typeL`或 `Series RL.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

0.0 A

程序使用名称

i_L_burden2_start

可计算

# Third winding burden inductance initial current — 第二个负载的初始感应电流
A | MA | kA | mA | nA | pA | uA

Details

第二个负载的初始电感电流。

依赖关系

要使用该参数,请将参数设置为

  • Include burdenModel the burden internally;

  • Burden typeL`或 `Series RL;

  • Number of windingsThree, Four, Five`或 `Six.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

0.0 A

程序使用名称

i_L_burden3_start

可计算

# Fourth winding burden inductance initial current — 第三负载的初始感应电流
A | MA | kA | mA | nA | pA | uA

Details

第三个负载的初始电感电流。

依赖关系

要使用该参数,请将参数设置为

  • Include burdenModel the burden internally;

  • Burden typeL`或 `Series RL;

  • Number of windingsFour, Five`或 `Six.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

0.0 A

程序使用名称

i_L_burden4_start

可计算

# Fifth winding burden inductance initial current — 第四负载的初始感应电流
A | MA | kA | mA | nA | pA | uA

Details

第四个负载的初始电感电流。

依赖关系

要使用该参数,请将参数设置为

  • Include burdenModel the burden internally;

  • Burden typeL`或 `Series RL;

  • Number of windingsFive`或 `Six.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

0.0 A

程序使用名称

i_L_burden5_start

可计算

# Sixth winding burden inductance initial current — 第五负载的初始感应电流
A | MA | kA | mA | nA | pA | uA

Details

第五个负载的初始电感电流。

依赖关系

要使用该参数,请将参数设置为

  • Include burdenModel the burden internally;

  • Burden typeL`或 `Series RL;

  • Number of windingsSix.

计量单位

A | MA | kA | mA | nA | pA | uA

默认值

0.0 A

程序使用名称

i_L_burden6_start

可计算

寄生

# Combined leakage inductance parasitic parallel conductance — 总散射电感的寄生并联电导
S | mS | nS | uS | 1/Ohm

Details

该参数用于表示与总散射电感并联的小寄生效应。某些电路拓扑建模可能需要小的并联电导。

依赖关系

要使用该参数,请将 Winding parameterized by 设置为 Combined primary and secondary values.

计量单位

S | mS | nS | uS | 1/Ohm

默认值

1e-9 1/Ohm

程序使用名称

g_Leq

可计算

# First leakage inductance parasitic parallel conductance — 第一绕组的寄生并联电导 散射电感
S | mS | nS | uS | 1/Ohm

Details

该参数用于表示与第一绕组散射电感平行的小寄生效应。某些电路拓扑建模可能需要小的并联电导。

依赖关系

要使用该参数,请将 Winding parameterized by 设置为 Separate primary and secondary values`或将 Number of windings 设置为 `Three, Four, Five`或 `Six.

计量单位

S | mS | nS | uS | 1/Ohm

默认值

1e-9 1/Ohm

程序使用名称

g_L1

可计算

# Second leakage inductance parasitic parallel conductance — 第二绕组的寄生并联电导 散射电感
S | mS | nS | uS | 1/Ohm

Details

该参数用于表示与第二绕组散射电感平行的微小寄生效应。

依赖关系

要使用该参数,请将 Winding parameterized by 设置为 Separate primary and secondary values`或将 Number of windings 设置为 `Three, Four, Five`或 `Six.

计量单位

S | mS | nS | uS | 1/Ohm

默认值

1e-9 1/Ohm

程序使用名称

g_L2

可计算

# Third leakage inductance parasitic parallel conductance — 第三绕组的寄生并联电导 散射电感
S | mS | nS | uS | 1/Ohm

Details

该参数用于表示与第三绕组散射电感平行的微小寄生效应。

依赖关系

要使用该参数,请将 Number of windings 设置为 Three, Four, Five`或 `Six.

计量单位

S | mS | nS | uS | 1/Ohm

默认值

1e-9 1/Ohm

程序使用名称

g_L3

可计算

# Fourth leakage inductance parasitic parallel conductance — 第四绕组的寄生并联电导 散射电感
S | mS | nS | uS | 1/Ohm

Details

该参数用于表示与第四绕组散射电感平行的小寄生效应。

依赖关系

要使用该参数,请将 Number of windings 设置为 Four, Five`或 `Six.

计量单位

S | mS | nS | uS | 1/Ohm

默认值

1e-9 1/Ohm

程序使用名称

g_L4

可计算

# Fifth leakage inductance parasitic parallel conductance — 第五绕组的寄生并联电导 散射电感
S | mS | nS | uS | 1/Ohm

Details

该参数用于表示与第五绕组散射电感平行的微小寄生效应。

依赖关系

要使用该参数,请将 Number of windings 设置为 Five`或 `Six.

计量单位

S | mS | nS | uS | 1/Ohm

默认值

1e-9 1/Ohm

程序使用名称

g_L5

可计算

# Sixth leakage inductance parasitic parallel conductance — 第六绕组的寄生并联电导 散射电感
S | mS | nS | uS | 1/Ohm

Details

该参数用于表示与第六绕组散射电感平行的微小寄生效应。

依赖关系

要使用该参数,请将 Number of windings 设置为 Six.

计量单位

S | mS | nS | uS | 1/Ohm

默认值

1e-9 1/Ohm

程序使用名称

g_L6

可计算

# Second winding burden inductance parasitic parallel conductance — 第一负载耗散电感的寄生并联电导
S | mS | nS | uS | 1/Ohm

Details

第一负载散射电感的寄生并联电导。

依赖关系

要使用该参数,请将 Include burden 设置为 Model the burden internally.

计量单位

S | mS | nS | uS | 1/Ohm

默认值

1e-9 1/Ohm

程序使用名称

g_L_burden2

可计算

# Third winding burden inductance parasitic parallel conductance — 第二负载散射电感的寄生并联电导
S | mS | nS | uS | 1/Ohm

Details

第二负载散射电感的寄生并联电导。

依赖关系

要使用该参数,请将 Include burden 设置为 Model the burden internally,并将 Number of windings 设置为 Three, Four, Five`或 `Six.

计量单位

S | mS | nS | uS | 1/Ohm

默认值

1e-9 1/Ohm

程序使用名称

g_L_burden3

可计算

# Fourth winding burden inductance parasitic parallel conductance — 第三负载耗散电感的寄生并联电导
S | mS | nS | uS | 1/Ohm

Details

第三负载散射电感的寄生并联电导。

依赖关系

要使用该参数,请将 Include burden 设置为 Model the burden internally`并将 Number of windings 设置为 `Four, Five`或 `Six.

计量单位

S | mS | nS | uS | 1/Ohm

默认值

1e-9 1/Ohm

程序使用名称

g_L_burden4

可计算

# Fifth winding burden inductance parasitic parallel conductance — 第四个负载的寄生并联电导 耗散电感
S | mS | nS | uS | 1/Ohm

Details

第四负载散射电感的寄生并联电导。

依赖关系

要使用该参数,请将 Include burden 设置为 Model the burden internally`并将 Number of windings 设置为 `Five`或 `Six.

计量单位

S | mS | nS | uS | 1/Ohm

默认值

1e-9 1/Ohm

程序使用名称

g_L_burden5

可计算

# Sixth winding burden inductance parasitic parallel conductance — 第五负载散射电感的寄生并联电导
S | mS | nS | uS | 1/Ohm

Details

第五负载散射电感的寄生并联电导。

依赖关系

要使用该参数,请将 Include burden 设置为 Model the burden internally`并将 Number of windings 设置为 `Six.

计量单位

S | mS | nS | uS | 1/Ohm

默认值

1e-9 1/Ohm

程序使用名称

g_L_burden6

可计算