Thyristor (Piecewise Linear)
页面进行中。 |
分段线性VAC的晶闸管。
类型: AcausalElectricPowerSystems.Semiconductors.Ideal.PiecewiseLinearThyristor
图书馆中的路径:
|
资料描述
座 Thyristor (Piecewise Linear) 模拟具有分段线性伏安特性(VAC)的晶闸管。 晶闸管的VAC使得如果栅极-阴极电压超过控制电极处的设定解锁电压,则晶闸管开路。 如果负载电流下降到设定的保持电流值以下,晶闸管就会关闭。
要设置表格式VAC,请选中该框 Enable thermal port ,而对于参数 On-state behavior and switching losses 设置值 Tabulate
.
在开路状态下,阳极-阴极通道表现得像线性二极管,具有直接的压降。 和开放状态下的阻力 . 但是,如果单元的热端口打开并且使用表格VAC对设备进行参数化,那么表格电阻将是温度和电流的函数。 在闭合状态下,阳极-阴极通道在闭合状态下表现得像具有低电导率的线性电阻器。 .
阳极-阴极电流的方程如下所示:
如果 满足两个条件之一。: 或 ,
在所有其他情况下 ,
哪里
-
-阳极-阴极电压;
-
-直流电压;
-
-栅极电压;
-
-解锁电压控制;
-
-阳极-阴极电流;
-
-保持电流;
-
-打开状态下的阻力;
-
-封闭状态下的导电性。
使用参数 Integral Diode ,一个内部保护二极管可以导通。 集成二极管通过提供用于反向电流的传导通道来保护半导体器件。 当半导体器件突然关闭负载电源时,电感负载会产生较大的反向电压浪涌。
设置参数值 Integral protection diode 视目的而定。
目标 | 选择的价值 | 内部保护二极管 |
---|---|---|
仿真速度的优先级。 |
|
正在添加内部块 Diode (Advanced). |
建模精度的优先级是准确地指示反向模式下的电荷动力学。 |
|
正在添加内部块 Diode (Advanced) 考虑到电荷动态。 |
栅极端口和热效应的仿真
您可以选择定向输入或电气端口来控制栅极,并使用热端口来模拟开关过程和传导损耗产生的热量。 要选择快门控制端口,请设置参数 Gate-control port 意义 Signal control port
或 Electrical control port
. 要使用热端口,请选中该框 Enable thermal port .
热损失
开关损耗是半导体热损耗的主要来源。 在每个通断开关期间,晶闸管的寄生元件累积然后耗散能量。
开关损耗取决于闭合状态下的电压和打开状态下的电流。 当接通开关器件时,功率损耗取决于器件上处于闭合状态的初始电压和器件完全打开时处于打开状态的最终电流。
该单元通过将转变温度提高等于损失除以转变的总热容量来计算开关损耗。 有必要指定一次开启时耗散的能量。 还需要指定关闭状态下的电压和打开状态下的电流的相应值,在该值下计算损耗。 您可以根据可用数据对通电损耗进行参数化。 如果可用,请使用表格数据。
-
要设置上电损耗的标量值,请设置参数 On-state behavior and switching losses 意义
Specify constant values
. 参数值 Switch-on loss 设置功率损耗量。 该装置在关闭状态下对电压损耗进行缩放,在打开状态下对电流进行缩放。 -
要将开关损耗设置为结温和开路状态下电流的函数,请设置参数 On-state behavior and switching losses 在值
Tabulate
. 参数 Switch-on loss, Eon(Tj,Iak) 设置损失金额。 单元在闭合状态下缩放电压损耗。
当电流降至参数值以下时 Holding current ,设备关闭。 参数值 Natural commutation rectification loss 检测停机期间的损耗。 该单元不按闭合状态下的电压或打开状态下的电流来缩放这些损耗,因为不可能确定何时测量初始电流或最终电压以用于整流损耗。
反向恢复损耗可能是二极管热损失的重要来源。 二极管在每次关断时耗散能量,从导电状态切换到开路状态。 模拟反向恢复损失:
-
选中此框 Enable thermal port .
-
为参数设置 Integral protection diode 意义
Diode with no dynamics
.
如果为参数 Reverse recovery loss model 值设置 Tabulated loss
,参数值 Reverse recovery loss table, Erec(Tj, If) 将耗散能量定义为紧接在开关事件之前的结温和正向电流的函数。 闭合状态下的电压相对于参数值线性缩放损耗 Turn-off voltage when measuring recovery loss, Vrec . 该表使用电流和电压的延迟值。 若要使用表中接近瞬时的值,请设置参数 Filter time constant for voltage and current values 小于最快切换周期的值。
如果为参数 Reverse recovery loss model 值设置 Fixed loss
,参数的值 Reverse recovery loss 确定每次关断时耗散的能量。 如果选中该复选框 Scale reverse recovery loss with current and voltage ,然后该块线性地缩放在打开状态下的电流损耗和在关闭状态下的电压的值。 要使用接近瞬时的缩放值,请将电压和电流值的滤波器时间常数设置为低于最快开关周期的值。
作为反向恢复建模的替代方法,可以设置参数 Integral protection diode 意义 Diode with charge dynamics
. 但是,与使用第一种方法相比,这种方法需要更短的建模时间步骤。
开关后的电流在仿真过程中是不知道的,因此当其值超过保持电流一段时间超过参数设置的值时,该单元将电流注册在打开状态。 Wait time before switch-on current measurement . 同样,当设备打开时,该单元将电压登记在关闭状态。 由于这个原因,记录的数据直到下一个开关周期才会在热模型中报告开关损耗。 如果您使用表格数据对开关损耗或反向恢复损耗进行建模,请确保温度和电流在您指定的范围内。 如果您没有定义现实的热模型,例如,如果结的热容量或结与外壳之间的电导率太低,那么温度可能超出您指定的范围,这可能导致将损失外推到非物理 |
港口
非定向
#
A
—
阳极
"电力"
Details
阳极连接的端口。
程序使用名称 |
|
#
K
—
阴极
"电力`
Details
阴极连接的端口。
程序使用名称 |
|
#
H
—
热端口
"温暖"
Details
的导热口。
依赖关系
要使用此端口,请选中此框 Enable thermal port .
程序使用名称 |
|
#
G
—
快门
"电力`
Details
门相连的端口。
依赖关系
要启用此端口,请设置参数 Gate-control port 意义 Electrical control port
.
程序使用名称 |
|
输入
#
G
—
快门
'标量`
Details
门相连的端口。
依赖关系
要启用此端口,请设置参数 Gate-control port 意义 Signal control port
.
数据类型 |
'漂浮64` |
复数支持 |
非也。 |
参数
主页
#
Gate-control port —
用于指定快门端口类型的选项
Signal control port
| Electrical control port
Details
用于指定交换机的快门控制端口的选项:
-
Signal control port
-单位使用方向输入端口控制快门; -
Signal control port
-单位使用非定向电端口控制快门。
值 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
无 |
#
Gate trigger voltage, Vgt —
解锁电压控制
V
| MV
| kV
| mV
Details
的栅极-阴极阈值电压。 当栅极-阴极电压超过此值时,器件导通。
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Holding current —
保持电流
A
| MA
| kA
| mA
| nA
| pA
| uA
Details
的当前阈值。 如果电流超过此值,即使栅极-阴极电压降至低于解锁控制电压,器件仍保持开启状态。
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
On-state behavior and switching losses —
工作模式行为和开关损耗
Specify constant values
| Tabulate
Details
工作模式行为和开关损耗的参数化方法:
-
Specify constant values
-使用标量值设置开关时的输出电流和损耗。 该模块假设在单个导通或关断开关期间耗散的能量线性地依赖于处于关断状态的电压和处于导通状态的电流。 该模块还假设损耗与温度无关。 -
Tabulate
-使用矢量设置输出电流和温度数据。 使用数组指定有关上电和断电损耗的数据。
依赖关系
若要使用此选项,请选中此框 Enable thermal port .
值 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
无 |
#
Forward voltage, Vf —
正向电压
V
| MV
| kV
| mV
Details
器导通的正向电压。
依赖关系
要使用此参数:
-
取消选中该框 Enable thermal port .
或:
-
勾选框 Enable thermal port ,而对于参数 On-state behavior and switching losses 设置值
Specify constant values
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
On-state resistance —
打开状态下的阻力
Ohm
| GOhm
| MOhm
| kOhm
| mOhm
Details
开的阳极-阴极通道的电阻。
依赖关系
要使用此参数:
-
取消选中该框 Enable thermal port .
或:
-
选中此框 Enable thermal port ,而对于参数 On-state behavior and switching losses 设置值
Specify constant values
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
On-state voltage, Vak(Tj,Iak) —
开路状态下的电压
V
| MV
| kV
| mV
Details
电压的矩阵在处于开路导电状态的器件上下降。 此参数取决于温度 Temperature vector, Tj 和开路状态下的最终输出电流 Anode-cathode current vector, Iak .
依赖关系
若要使用此选项,请选中此框 Enable thermal port ,而对于参数 On-state behavior and switching losses 设置值 Tabulate
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Temperature vector, Tj —
温度值
K
| degC
| degF
| degR
| deltaK
| deltadegC
| deltadegF
| deltadegR
Details
电压被设置在打开状态的温度值的向量 On-state voltage, Vak(Tj,Iak) .
依赖关系
若要使用此选项,请选中此框 Enable thermal port ,而对于参数 On-state behavior and switching losses 设置值 Tabulate
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Anode-cathode current vector, Iak —
阳极-阴极电流值
A
| MA
| kA
| mA
| nA
| pA
| uA
Details
电压被设置在开路状态的阳极-阴极电流的值的向量 On-state voltage, Vak(Tj,Iak) . 第一个元素必须为零。
依赖关系
若要使用此选项,请选中此框 Enable thermal port ,而对于参数 On-state behavior and switching losses 设置值 Tabulate
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Off-state conductance —
封闭状态电导率
S
| mS
| nS
| uS
| 1/Ohm
Details
阳极-阴极导电体处于闭合状态。 此参数的值应小于 ,在哪里 -参数值 On-state resistance .
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
开关损耗
#
Switch-on loss, Eon(Tj,Iak) —
开关损耗矩阵
Btu_IT
| J
| MJ
| MWh
| Wh
| eV
| kJ
| kWh
| mJ
| mWh
Details
在单次开关期间耗散的能量作为温度的函数 Temperature vector for switching losses, Tj 和开路状态下的最终输出电流 Anode-cathode current vector for switching losses, Iak .
依赖关系
若要使用此选项,请选中此框 Enable thermal port ,而对于参数 On-state behavior and switching losses 设置值 Tabulate
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Temperature vector for switching losses, Tj —
温度值向量
K
| degC
| degF
| degR
| deltaK
| deltadegC
| deltadegF
| deltadegR
Details
开关时设置损耗的温度值向量 Switch-on loss, Eon(Tj,Iak) .
依赖关系
若要使用此选项,请选中此框 Enable thermal port ,而对于参数 On-state behavior and switching losses 设置值 Tabulate
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Anode-cathode current vector for switching losses, Iak —
阳极-阴极电流值
A
| MA
| kA
| mA
| nA
| pA
| uA
Details
阳极-阴极电流值的矢量,在该矢量上,开关时设置损耗 Switch-on loss, Eon(Tj,Iak) . 第一个元素必须为零。
依赖关系
若要使用此选项,请选中此框 Enable thermal port ,而对于参数 On-state behavior and switching losses 设置值 Tabulate
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Switch-on loss —
开关损耗
Btu_IT
| J
| MJ
| MWh
| Wh
| eV
| kJ
| kWh
| mJ
| mWh
Details
单次上电过程中耗散的能量。
依赖关系
若要使用此选项,请选中此框 Enable thermal port ,而对于参数 On-state behavior and switching losses 设置值 Specify constant values
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Natural commutation rectification loss —
自然开关整流损耗
Btu_IT
| J
| MJ
| MWh
| Wh
| eV
| kJ
| kWh
| mJ
| mWh
Details
当电流降至保持电流以下时,器件关闭时发生的整流损耗。 此参数设置为标量值。
依赖关系
若要使用此选项,请选中此框 Enable thermal port .
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Off-state voltage for switching loss data —
损耗数据的闭合状态下的电压
V
| MV
| kV
| mV
Details
器的输出电压处于关闭状态。 这是确定开和关损耗的锁定电压。
依赖关系
若要使用此选项,请选中此框 Enable thermal port .
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
On-state current for switching loss data —
输出电流
A
| MA
| kA
| mA
| nA
| pA
| uA
Details
确定导通损耗、关断损耗和开路电压的输出电流。 将此参数设置为标量值。
该参数是在栅极电压下降到参数值以下的时刻测量的。 Gate trigger voltage, Vgt . 开关脉冲的持续时间超过电流达到其最大值所需的时间。 |
依赖关系
若要使用此选项,请选中此框 Enable thermal port .
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Wait time before switch-on current measurement —
时间测量打开状态下的电流
d
| s
| hr
| ms
| ns
| us
| min
Details
在开路状态下测量电流之前的等待时间。
依赖关系
若要使用此选项,请选中此框 Enable thermal port .
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
积分二极管
#
Integral protection diode —
内部保护二极管(抑制器)
External Diode
| Diode with no dynamics
| Diode with charge dynamics
Details
默认值为 External Diode
.
如果有必要打开内部保护二极管,那么有两种可能的选择:
-
Diode with no dynamics
. -
Diode with charge dynamics
.
值 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
无 |
#
Diode model —
二极管模型
Piecewise linear
| Tabulated I-V curve
Details
选择二极管型号之一:
-
Piecewise linear
-使用具有分段线性VAC的二极管,有关更多信息,请参阅 分段线性VAC二极管 -
Tabulated I-V curve
-具有制表VAC的二极管用于正向偏置和反向偏置的恒定电导率。
依赖关系
若要使用此选项,请选中此框 Enable thermal port ,而对于参数 Integral protection diode 设置值 Diode with no dynamics
或 Diode with charge dynamics
.
值 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
无 |
#
Table type —
表格功能
Table in If(Tj, Vf) form
| Table in Vf(Tj, If) form
Details
选择一个表格函数:电流作为温度和电压的函数,或电压作为温度和电流的函数。
依赖关系
要使用此参数,请设置:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
或Diode with charge dynamics
; -
为参数 Diode model 意义
Tabulated I-V curve
.
值 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
无 |
#
Forward currents, If(Tj, Vf) —
直流电的矩阵
A
| MA
| kA
| mA
| nA
| pA
| uA
Details
正向电流值作为温度的函数 Junction temperatures, Tj 和紧张 Forward voltages, Vf .
依赖关系
要使用此参数,请设置:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
或Diode with charge dynamics
; -
为参数 Diode model 意义
Tabulated I-V curve
; -
为参数 Table type 意义
Table in If(Tj, Vf) form
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Forward voltages, Vf(Tj, If) —
正向电压矩阵
V
| MV
| kV
| mV
Details
正向电压值作为温度的函数 Junction temperatures, Tj 和电流 Forward currents, If .
依赖关系
要使用此参数,请设置:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
或Diode with charge dynamics
; -
为参数 Diode model 意义
Tabulated I-V curve
; -
为参数 Table type 意义
Table in Vf(Tj, If) form
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Junction temperatures, Tj —
转变温度值向量
K
| degC
| degF
| degR
| deltaK
| deltadegC
| deltadegF
| deltadegR
Details
设定正向电压时的转变温度值向量 Forward voltages, Vf(Tj, If) 或直流电流 Forward currents, If(Tj, Vf) . 此向量必须至少包含两个元素。
依赖关系
要使用此参数,请设置:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
或Diode with charge dynamics
; -
为参数 Diode model 意义
Tabulated I-V curve
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Forward voltages, Vf —
正向电压值的向量
V
| MV
| kV
| mV
Details
设置正向电流的正向电压值矢量 Forward currents, If(Tj, Vf) . 此向量必须包含至少三个非负元素。
依赖关系
要使用此参数,请设置:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
或Diode with charge dynamics
; -
为参数 Diode model 意义
Tabulated I-V curve
; -
为参数 Table type 意义
Table in If(Tj, Vf) form
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Forward currents, If —
正向电流值的向量
A
| MA
| kA
| mA
| nA
| pA
| uA
Details
设置正向电压的正向电流值的矢量 Forward voltages, Vf(Tj, If) . 此向量必须包含至少三个非负元素。
依赖关系
要使用此参数,请设置:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
或Diode with charge dynamics
; -
为参数 Diode model 意义
Tabulated I-V curve
; -
为参数 Table type 意义
Table in Vf(Tj, If) form
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Forward voltage —
直流电压
V
| MV
| kV
| mV
Details
二极管的阳极和阴极之间的最小电压以使二极管的伏安特性的梯度等于1/ ,在哪里 -参数值 On resistance .
依赖关系
要使用此参数:
-
取消选中该框 Enable thermal port ;
-
为参数设置 Integral protection diode 意义
Diode with no dynamics
或Diode with charge dynamics
;
或安装:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
或Diode with charge dynamics
; -
为参数 Diode model 意义
Piecewise linear
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
On resistance —
直接接通时的电阻
Ohm
| GOhm
| MOhm
| kOhm
| mOhm
Details
当电压高于参数设置的值时,二极管的电阻处于开路状态 Forward voltage .
依赖关系
要使用此参数:
-
取消选中该框 Enable thermal port ;
-
为参数设置 Integral protection diode 意义
Diode with no dynamics
或Diode with charge dynamics
;
或安装:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
或Diode with charge dynamics
; -
为参数 Diode model 意义
Piecewise linear
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Off conductance —
封闭状态电导率
S
| mS
| nS
| uS
| 1/Ohm
Details
二极管重新导通时的电导率。
依赖关系
若要使用此参数,请为参数设置 Integral protection diode 意义 Diode with no dynamics
或 Diode with charge dynamics
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Junction capacitance —
转移能力
F
| mF
| nF
| pF
| uF
Details
从耗尽区过渡的电容特性的值,充当电介质并分离阳极和阴极的连接。
依赖关系
若要使用此参数,请为参数设置 Integral protection diode 意义 Diode with charge dynamics
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Peak reverse current, iRM —
峰值反向电流
A
| MA
| kA
| mA
| nA
| pA
| uA
Details
外部测试电路测得的返回电流峰值。 此值必须小于零。
依赖关系
若要使用此参数,请为参数设置 Integral protection diode 意义 Diode with charge dynamics
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Initial forward current when measuring iRM —
iRM测量期间的初始正向电流
A
| MA
| kA
| mA
| nA
| pA
| uA
Details
测量峰值反向电流时的初始正向电流(在接通时间的初始时刻)。 此值必须大于零。
依赖关系
若要使用此参数,请为参数设置 Integral protection diode 意义 Diode with charge dynamics
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Rate of change of current when measuring iRM —
iRM测量期间电流的变化率
A/s
| A/us
Details
测量峰值反向电流时的电流的变化率。 此值必须小于零。
依赖关系
若要使用此参数,请为参数设置 Integral protection diode 意义 Diode with charge dynamics
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Reverse recovery time parameterization —
类型的反向恢复时间确定
Specify stretch factor
| Specify reverse recovery time directly
| Specify reverse recovery charge
Details
选择选项时 Specify stretch factor
或 Specify reverse recovery charge
块用于计算反向恢复时间的值来指定。
依赖关系
若要使用此参数,请为参数设置 Integral protection diode 意义 Diode with charge dynamics
.
值 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
无 |
# Reverse recovery time stretch factor — 反向恢复时间的拉伸系数
Details
块用于计算的值 Reverse recovery time, trr . 此值必须大于`1'。 与指定反向恢复电荷相比,指定拉伸系数是参数化反向恢复时间的更简单方法。 拉伸系数的值越高,反向恢复电流耗散的时间越长。
依赖关系
若要使用此参数,请为参数设置 Integral protection diode 意义 Diode with charge dynamics
,而对于参数 Reverse recovery time parameterization 意义 Specify stretch factor
.
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Reverse recovery time, trr —
反向恢复时间
d
| s
| hr
| ms
| ns
| us
| min
Details
当二极管两端的电压从正向偏置反转到反向时,二极管关闭所需的时间。
电流通过零(当二极管关断时)的初始转变的瞬间与电流下降到小于峰值电流的10%的瞬间之间的间隔。 参数值 Reverse recovery time, trr 必须有超过参数值。 Peak reverse current, iRM ,除以参数值 Rate of change of current when measuring iRM .
依赖关系
若要使用此参数,请为参数设置 Integral protection diode 意义 Diode with charge dynamics
,而对于参数 Reverse recovery time parameterization 意义 Specify reverse recovery time directly
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Reverse recovery charge, Qrr —
反向恢复费用
C
| Ah
| mC
| nC
| uC
| MAh
| kAh
| mAh
| s*uA
Details
块用于计算的值 Reverse recovery time, trr . 如果在块参数中指定反向恢复时间值作为反向恢复时间确定的类型而不是反向恢复时间值,则使用此参数。
反向恢复电荷是二极管关断后继续耗散的总电荷。 值必须小于 ,在哪里:
-
-为参数指定的值 Peak reverse current, iRM ;
-
-为参数指定的值 Rate of change of current when measuring iRM .
依赖关系
若要使用此参数,请为参数设置 Integral protection diode 意义 Diode with charge dynamics
,而对于参数 Reverse recovery time parameterization 意义 Specify reverse recovery charge
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Reverse recovery loss model —
反向恢复损失模型
Fixed loss
| Tabulated loss
Details
选择反向恢复期间的损失建模方式:作为固定值或表格函数。
依赖关系
若要使用此选项,请选中此框 Enable thermal port ,而对于参数 Integral protection diode 设置值 Diode with no dynamics
.
值 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
无 |
#
Reverse recovery loss —
反向恢复损失
Btu_IT
| J
| MJ
| MWh
| Wh
| eV
| kJ
| kWh
| mJ
| mWh
Details
在每次关断时耗散的能量,而不管开关之前或之后二极管的状态如何。
依赖关系
要使用此参数,请设置:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
; -
为参数 Reverse recovery loss model 意义
Fixed loss
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
# Scale reverse recovery loss with current and voltage — 利用电流和电压调整反向恢复损耗
Details
选择此选项可使用电流和电压调整反向恢复损耗。
依赖关系
要使用此参数,请设置:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
; -
为参数 Reverse recovery loss model 意义
Fixed loss
.
默认值 |
|
程序使用名称 |
|
可计算 |
无 |
#
Reverse recovery loss table, Erec(Tj, If) —
反向恢复损失矩阵
Btu_IT
| J
| MJ
| MWh
| Wh
| eV
| kJ
| kWh
| mJ
| mWh
Details
耗散能量作为电流的函数 Forward current vector for recovery loss table, If 就在开关和温度事件之前 Temperature vector for recovery loss table, Tj .
依赖关系
要使用此参数,请设置:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
; -
为参数 Reverse recovery loss model 意义
Tabulated loss
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Temperature vector for recovery loss table, Tj —
温度值向量
K
| degC
| degF
| degR
| deltaK
| deltadegC
| deltadegF
| deltadegR
Details
设定反向恢复损失的温度值向量 Reverse recovery loss table, Erec(Tj, If) .
依赖关系
要使用此参数,请设置:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
; -
为参数 Reverse recovery loss model 意义
Tabulated loss
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Forward current vector for recovery loss table, If —
正向电流值的向量
A
| MA
| kA
| mA
| nA
| pA
| uA
Details
指定反向恢复损耗的正向电流值向量 Reverse recovery loss table, Erec(Tj, If) .
依赖关系
要使用此参数,请设置:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
; -
为参数 Reverse recovery loss model 意义
Tabulated loss
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Forward current when measuring recovery loss, Irec —
测量恢复损耗时的直流电
A
| MA
| kA
| mA
| nA
| pA
| uA
Details
直流电流通过二极管进行反向恢复,该装置用于测量恢复损耗。
依赖关系
要使用此参数,请设置:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
; -
为参数 Reverse recovery loss model 意义
Fixed loss
; -
国旗 Scale reverse recovery loss with current and voltage .
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Turn-off voltage when measuring recovery loss, Vrec —
测量恢复损耗时的关断电压
V
| MV
| kV
| mV
Details
反向恢复后二极管两端的电压用于测量恢复损耗。
依赖关系
要使用此参数,请设置:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
; -
为参数 Reverse recovery loss model 意义
Fixed loss
; -
国旗 Scale reverse recovery loss with current and voltage ;
或安装:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
; -
为参数 Reverse recovery loss model 意义
Tabulated loss
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Filter time constant for voltage and current values —
电压和电流值的滤波时间常数
d
| s
| hr
| ms
| ns
| us
| min
Details
用于计算反向恢复损耗的电压和电流值的滤波时间常数。 将此参数的值设置为低于最快切换周期。
依赖关系
要使用此参数,请设置:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
; -
为参数 Reverse recovery loss model 意义
Fixed loss
; -
国旗 Scale reverse recovery loss with current and voltage ;
或安装:
-
国旗 Enable thermal port ;
-
为参数 Integral protection diode 意义
Diode with no dynamics
; -
为参数 Reverse recovery loss model 意义
Tabulated loss
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
热端口
# Enable thermal port — 打开热端口
Details
选择此选项可使用单元的热端口并模拟产生的热量和设备温度的影响。
默认值 |
|
程序使用名称 |
|
可计算 |
无 |
#
Thermal network —
选择内部热模型
Specify junction and case thermal parameters
| Cauer model
| Cauer model parameterized with Foster coefficients
| External
Details
选择内部热模型:
-
Specify junction and case thermal parameters
; -
Cauer model
; -
Cauer model parameterized with Foster coefficients
; -
External
.
值 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
无 |
#
Junction-case and case-ambient (or case-heatsink) thermal resistances, [R_JC R_CA] —
热阻矢量
K/W
Details
向量'[R_JC R_CA]'由两个热阻值组成。 `R_JC’的第一个值是结和外壳之间的热阻。 第二个值’R_CA’是*H*端口与器件主体之间的热阻。
依赖关系
若要使用此参数,请为参数设置 Thermal network 意义 Specify junction and case thermal parameters
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Thermal resistances, [R1 R2 ... Rn] —
考尔模型的热阻矢量
K/W
Details
矢量从 由加热网络中的Kauer元件表示的热阻值。 所有这些值必须大于零。
依赖关系
若要使用此参数,请为参数设置 Thermal network 意义 Cauer model
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Thermal resistances, [R1 R2 ... Rn] —
福斯特模型的热阻矢量
K/W
Details
矢量从 热阻值由Foster模型在加热网络中的系数表示。 所有这些值必须大于零。
依赖关系
若要使用此参数,请为参数设置 Thermal network 意义 Cauer model parameterized with Foster coefficients
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Thermal mass parameterization —
热容量参数化
By thermal time constants
| By thermal mass
Details
选择设置热容量的方法:
-
By thermal time constants
-热时间常数方面的热容量的参数化。 默认情况下使用此值。 -
By thermal mass
-设置热容值。
依赖关系
若要使用此参数,请为参数设置 Thermal network 意义 Specify junction and case thermal parameters
, Cauer model
或 Cauer model parameterized with Foster coefficients
.
值 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
无 |
#
Junction and case thermal time constants, [t_J t_C] —
热时间常数向量
d
| s
| hr
| ms
| ns
| us
| min
Details
向量'[t_J t_C]'由热时间常数的两个值组成。 `T_J’的第一个值是热转变时间常数。 第二个值’t_C’是外壳的热时间常数。
依赖关系
若要使用此参数,请为参数设置 Thermal network 意义 Specify junction and case thermal parameters
,而对于参数 Thermal mass parameterization 意义 By thermal time constants
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Thermal time constants, [t1 t2 ... tn] —
考尔模型的热时间常数向量
d
| s
| hr
| ms
| ns
| us
| min
Details
矢量从 热时间常数的值,其中 这是加热网络中Kauer元件的数量。 所有这些值必须大于零。
热容的值计算为 ,在哪里 , 和 -热容量、热时间常数及热阻 -Cowera的go元素。
依赖关系
若要使用此参数,请为参数设置 Thermal network 意义 Cauer model
,而对于参数 Thermal mass parameterization 意义 By thermal time constants
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Thermal time constants, [t1 t2 ... tn] —
福斯特模型的热时间常数向量
d
| s
| hr
| ms
| ns
| us
| min
Details
矢量从 热时间常数的值,其中 这是供暖网络中福斯特模型的系数数。 所有这些值必须大于零。
热容的值计算为 ,在哪里 , 和 -热容量、热时间常数及热阻 -Cowera的go元素。
依赖关系
若要使用此参数,请为参数设置 Thermal network 意义 Cauer model parameterized with Foster coefficients
,而对于参数 Thermal mass parameterization 意义 By thermal time constants
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Junction and case thermal masses, [M_J M_C] —
考尔模型的热容值向量
J/K
| kJ/K
Details
向量'[M_J M_C]'由热容的两个值组成。 `M_J’的第一个值是结的热容量。 第二个值’M_C’是外壳的热容量。
依赖关系
若要使用此参数,请为参数设置 Thermal network 意义 Specify junction and case thermal parameters
,而对于参数 Thermal mass parameterization 意义 By thermal mass
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Thermal masses, [M1 M2 ... Mn] —
考尔模型的热容值向量
J/K
| kJ/K
Details
矢量从 热容值,其中 这是热网中Kauer模型的系数数。 所有这些值必须大于零。
依赖关系
若要使用此参数,请为参数设置 Thermal network 意义 Cauer model
,而对于参数 Thermal mass parameterization 意义 By thermal mass
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Thermal masses, [M1 M2 ... Mn] —
福斯特模型的热容值向量
J/K
| kJ/K
Details
矢量从 热容值,其中 这是加热网络中福斯特元件的数量。 所有这些值必须大于零。
依赖关系
若要使用此参数,请为参数设置 Thermal network 意义 Cauer model parameterized with Foster coefficients
,而对于参数 Thermal mass parameterization 意义 By thermal mass
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Junction and case initial temperatures, [T_J T_C] —
热时间常数向量
K
| degC
| degF
| degR
| deltaK
| deltadegC
| deltadegF
| deltadegR
Details
向量'[t_J t_C]'由热时间常数的两个值组成。 `T_J’的第一个值是热转变时间常数。 第二个值’t_C’是外壳的热时间常数。
依赖关系
若要使用此参数,请为参数设置 Thermal network 意义 Specify junction and case thermal parameters
,而对于参数 Thermal mass parameterization 意义 By thermal time constants
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Thermal masses initial temperatures, [T1 T2 ... Tn] —
考尔模型的初始温度矢量
K
| degC
| degF
| degR
| deltaK
| deltadegC
| deltadegF
| deltadegR
Details
温度值的向量。 它对应于模型中每个热容量的温差。
依赖关系
若要使用此参数,请为参数设置 Thermal network 意义 Cauer model
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Initial node temperatures, [T1 T2 ... Tn] —
福斯特模型的初始温度向量
K
| degC
| degF
| degR
| deltaK
| deltadegC
| deltadegF
| deltadegR
Details
福斯特模型的每个元素的绝对温度值的向量。
依赖关系
若要使用此参数,请为参数设置 Thermal network 意义 Cauer model parameterized with Foster coefficients
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |
#
Junction thermal mass —
过渡热容量
J/K
| kJ/K
Details
过渡热容量
依赖关系
若要使用此参数,请为参数设置 Thermal network 意义 External
.
计量单位 |
|
默认值 |
|
程序使用名称 |
|
可计算 |
是 |